BREDENT LIQUIDS SUPPORT

Ceram-Bond

Before using this product, please read and follow these instructions carefully.

1. Indication Range

Ceram Bond is a ceramic material which is used as a layer between all metals and ceramic. It compensates differences in the expansion coefficients between metal and ceramic and blocks escaping metal oxides.

2. Processing

2.1. Preparation of the object:

After finishing, sandblast the framework with aluminium oxide. Then clean thoroughly with distilled water in the ultrasonic unit for ten minutes or using the steam cleaner. Afterwards the metal surface must not be touched any more.

2.2. Applying Ceram Bond:

Use a brush for stains to apply one covering coat with a uniform layer thickness onto the metal surface.

2.3. Predrying Ceram Bond in the ceramic furnace:

Open the ceramic furnace which has been preheated to 650° C and dry the framework onto which Ceram Bond has been applied for one minute in the open furnace.

2.4. Firing Ceram Bond in the ceramic furnace:

Firing of Ceram Bond is started at 650° C and continued up to 980° C. The temperature increase rate is 55° C/minute. Firing is performed under vacuum. After completion of the firing process, the framework is immediately removed from the furnace. After firing, the framework should exhibit a beige to golden yellow color.

2.5. Opaque firing and further processing:

Apply the opaque material – according to the tooth shade – onto the fired Ceram Bond. A wash bake is not required. Then further processing is carried out according to the instructions of the manufacturer of the ceramic material.

3. Error sources and their elimination:

To ensure successful use, we recommend to test the desired alloy with Ceram Bond.

3.1. Cracks in Ceram Bond:

Ceram Bond was applied too thickly (very fine cracks are acceptable/normal)! Sandblast the material and reapply as described above.

3.2. Bubbles in Ceram Bond:

The metal must be degased. Sandblast Ceram Bond and degas the framework at 980° C under vacuum for ten minutes before Ceram Bond is applied again.

3.3. Green and/or blacks spots in Ceram Bond:

Ceram Bond was applied too thinly or the framework was wet or greasy.

3.4 Cracks in the ceramic:

If Ceram Bond reveals a rusty brown color after firing, the alloy is not suitable. Please use a different alloy.

The following alloys have proved to be unsuitable: Crutanium by Krupp Austenal, Crysatalloy by Shofu and Ticonium.

4. Safety recommendations and hazard warnings

4.1. Personal protective equipment:

When processing Ceram Bond, protective gloves, safety goggles and protective working clothes must be worn.

4.2. Skin contact:

Wash off immediately using water and soap and rinse carefully.

4.3. Eye contact:

Rinse eyes for several minutes under running water with eyelid being opened.

4.4. After swallowing:

If complaints persist, seek medical attention.

5. Storage and durability:

5.1. The product must be stored in the sealed container under dry conditions. If proper storage is ensured, the product features unlimited durability.

5.2. Proper disposal: Ceram Bond can be disposed of together with the regular household garbage.

6. Additional information

The information contained in these instructions for use is always updated according to the latest knowledge and experience. Therefore we recommend to read the instructions for use again before using a new package. These instructions for use refer to Ceram Bond, Order No. 520 0032 2 and 520 0032 3.

Chrome Cobalt Bonding Agent

INSTRUCTIONS FOR USE CHROME COBALT BONDING AGENT

Before using this product, please read and follow these instructions carefully.

1. Indication Range:
Chrome Cobalt Bonding Agent (CKB) is a ceramic material. It is used to form a layer between all metals and ceramic. It compensates for different expansion coefficients between metal and ceramic and blocks escaping metal oxides.

2. Processing

2.1 Preparation of the object:
After finishing, blast the object with aluminum oxide. Clean it carefully with distilled water in the ultrasonic unit or with a steam-blasting unit. After this process, the metal surface must not be touched any more.

2.2 Mixing:
Mix the Chrome Cobalt Bonding Agent with distilled water to obtain a thin consistency. Other mixing liquids are not suitable.

2.3 Applying the Chrome Cobalt Bonding Agent:
Use a staining brush to apply a single covering layer of the mixed CKB onto the metal surface. A uniform, pink color should result on the surface.
Please note: Once the CKB has dried, it must be mixed anew!

2.4 Firing on the Chrome Cobalt Bonding Agent in the ceramic furnace:
Firing of the CKB is started at 650º C and is continued up to a temperature of 980º C. The rate is 55º C per minute. The firing time amounts to 6 minutes. Firing is performed under vacuum. After firing, the frame must be immediately taken out of the furnace. The frame should have a golden-yellow to beige color after firing.

2.5 Opaque firing and further processing:
A covering layer of opaque - which corresponds to the tooth shade - is applied onto the fire Chrome Cobalt Bonding. A washbake is not required. Then continue according to the instructions of the manufacturer of the ceramic material.

2.6 Sources of errors and how to eliminate them:
Chrome Cobalt Bonding Agent has been used in numerous laboratories since the middle of 1992. To ensure successful application, we recommend testing the desired alloy with CKB.

2.6.1 Cracks in the Chrome Cobalt Bonding Agent:
Too much CKB has been applied! Blast the material and apply anew according to the instructions.

2.6.2 Bubbles in the Chrome Cobalt Bonding Agent:
Degassing of the metal is required. Blast the material and - prior to the firing CKB anew - degas the frame under vacuum at 980º C.

2.6.3 Green and/or black stains in the Chrome Cobalt Bonding Agent:
CKB was mixed too thinly or the frame was moist or greasy. Stains may also result if dried CKB has been mixed anew. Blast CKB, clean the frame and then apply CKB anew.

2.6.4 Cracks in the ceramic:
If the Chrome Cobalt Bonding Agent displays a rust-like brown color after firing, the alloy is not suitable. Please use a different alloy. Up until today the following alloys have proved to be not suitable: Crutanium by Krupp Austenal, Crystalloy by Shofy and Ticonium. Cracks may also result, if dried CKB has been mixed anew since it is not ensured that the different expansion coefficients are compensated.

3. Safety recommendations and hazard warnings
3.1 Protective clothing
While processing Chrome Cobalt Bonding Agent, dust mask, safety gloves, goggles and protective clothing must be worn.

3.2 To ensure safe handling of this product, the formation of dust must be avoided.

3.3 After skin contact:
Immediately wash off with water and soap and rinse thoroughly. Normally, this product does not irritate the skin. After eye contact: Rinse eyes carefully with running water with eyelid open. After ingesting: If problems persist, seek medical attention.

4. Storage and durability

4.1 This product must be sealed well and stored dry. If proper storage is ensured, this product has almost unlimited shelf life.

4.2 Proper disposal:
Product can be disposed of with household garbage.

5. Further information

The information contained in these instructions for use is always updated according to the latest knowledge and experience.
Therefore, we recommend that you read these instructions again before using a new package.
These instructions refer to Chrome Cobalt Bonding Agent, Item #s 520 003 20 and 520 003 21.

MATERIAL SAFETY DATA SHEET
Product Name: CHROME COBALT BONDING AGENT
Product Code: 520 003 20, 520 003 21

Before using this product, please read and follow these instructions carefully.

1. Composition/Information on ingredients
Product Description/use: Ceramic material with bonding agents and pigments.
Hazardous Substances: Pentane.
Name: CAS-No. Content Hazard Symbol Hazard Codes.
Titanium dioxide 13463-67 5 - 10% None.

2. Hazard Identification
Special hazard warning: R 34 Causes acid burning.
R 36/37/38 Irritant to eyes, respiratory organs and skin. Harmful effects/symptoms: itching, burning skin.

3. First aid procedures:
In general: Any articles of clothing contaminated with this product must be removed immediately. After skin contact: Immediately flush with water and soap and rinse thoroughly. Normally, this product does not cause irritation of the skin. After eye contact: Rinse eyes with lid open with running water for several minutes. After ingestion: If problems persist, seek medical attention.

4. Fire fighting procedures:
Suitable extinguishing media: Not applicable. This product is non flammable.

5. Accidental release procedures:
Person-related procedures: No special procedures required.
Environmental protection procedures: No special procedures required.
Cleaning/removal procedures: Wipe off with a wet cloth and dispose with household garbage.

6. Storage and handling:
Storage: Store in well-sealed containers under dry conditions. Handling: Avoid formation of dust.

7. Exposure limit and personal protective equipment
Ingredients with working-place related limits:
CAS No.: Description Type Value Unit
13463-67-7 Titanium dioxide TLV 6F mg/m3
Additional information: The lists that were valid during the preparation of these data sheets served as reference documents.
Personal protective equipment:
Respiratory protection: Mechanical filter respirator.
Hand protection: Protective gloves.
Eye protection: Safety glasses.
Protection of body: Protective clothing.
Protective & hygienic measures: The usual precautions for the handling of chemicals have to be observed.

8. Physical and chemical properties:
Appearance:
Form: Powder.
Color: Pink
Odor: Odorless.
Data relevant to safety:
pH (when supplied): Not applicable.
pH for 100 g/l H2O and 20º C: Approx. 7
Flash point (º C): Not applicable.
Melting point: Approx. 800
Solubility in water: Practically insoluble.

9. Stability and reactivity:
Conditions to avoid: In case of proper use, no reaction.
Materials to avoid: With acids if possible.
Hazardous decomposition products: Up to 1200º C no decomposition products known.

10. Toxicological information:
LD50/LC50 components Type Value Species
Titanium dioxide Oral > 20,000 mg/kg Rat
Dermal > 10,000 mg/kg Rabbit
Inhalatory >6.8 mg/l 4h Rat
Irritating properties: On skin; no irritant effect on eyes (if any, possibly due to mechanical influence - dust).
Sensitization: No sensitizing effect known.
Carcinogenic, teratogenic or mutagenic effects: No such effects known.

11. Ecological information:
General information: Must not reach waterways or sewage system.

12. Disposal consideration:
Product/Soiled Container: Product and soiled container must be disposed in a suitable container and in agreement with local and national regulations.

13. Export regulation
Material designation: Non hazardous material.
Air traffic: Non hazardous material.
Marine traffic: Non hazardous material.

14. Regulatory information:
Hazard symbol & identification: Not applicable.
Hazardous substances:
Hazard codes: Not applicable.
Safety codes: Not applicable.

15. Other information
Data sheet completed by: Research & Development Dept. - Bredent (Germany).
This Material Safety Data Sheet is provided by way of guide for the use of our product and is correct to the best of our knowledge.
However, we can't offer any guarantee as to its accuracy or exhaustiveness. All chemicals may present unforeseen risks and should be used with caution.
We cannot guarantee that the risks referred above are the only risks present. The final choice of the application of a product is thus the sole responsibility of the user.

1. Pre-treating the metal coping

After trimming and finishing the coping, sandblast it. Following this, the coping should either be boiled for 10 minutes in distilled water or thoroughly steam cleaned. At this stage the coping should only be held with tweezers. The coping must be thoroughly dried before the chrome cobalt bonding agent is applied.

2. Applying the bonding agent

Mix the chrome cobalt bonding agent into a thin consistency using distilled water. Apply one masking coat of chrome cobalt bonding agent with a staining brush. While doing so, go over the metal/porcelain junctures to avoid discolorations in the border zones.

Important:Chrome cobalt bonding agent can be mixed only once. Should the mix dry out, it is no longer suitable for use.

3. Firing the chrome cobalt bonding agent

May vary according to individual furnaces.

Recommended values:
Initial Temperature: 650ºC.
Final Temperature: 980ºC in vacuum.
Rate of Temperature increase: 55ºC per minute.
Once the final temperature has been reached, remove the coping from the furnace. The coping should now have a yellow or golden yellowish appearance. At this stage, the opaque can be applied, according to the porcelain manufacturer’s instructions.

Cracks in the chrome cobalt bonding agent:

Consistency or layer too thick. Sand-blast and reapply properly.

Blisters in the chrome cobalt bonding agent:

We recommend degassing the coping before the bonding agent is fired, by heating to 980ºC in vacuum and holding for 10 minutes.

Green/Black spots:

Either the bonding agent was mixed too thinly, the coping was moist or greasy or dried out material was re-used.

Cracks in the porcelain:

Can occur if the metal coping is disproportionately small in relation to the volume of the porcelain or if the metal connectors are defective. Should a reddish-brown layer appear instead of a yellow one, then the alloy is unsuitable. Simply use another commercially available chrome cobalt alloy.

To date, only three alloys have been proven unsuitable :

Crutanium, Crystalloy and Ticonium.

Microanalysis of the porcelain content

Since 1982, many dental laboratories have successfully worked with our chrome cobalt bonding system. Despite this, we recommend testing the bond on a sprue button made from your chrome cobalt alloy. Poorly processed alloys can also lead to defects. Often alloys are overheated and burnt during casting.

Colloidal Graphite

MATERIAL SAFETY DATA SHEET
Product Name: COLLOIDAL GRAPHITE
Product Code: 540 007 06

Before using this product, please read and follow these instructions carefully.

1. Composition/Information on ingredients
Product Description/use: Graphite-suspension in isopropanol.
Hazardous Substances:
Name: CAS-No. Content Hazard symbols Hazard codes
Isopropanol 67-63-0 60 - 90% by w. F R 11

2. Hazard Identification F Flammable
Hazard codes R 11 Highly flammable.

3. First aid procedures:
Inhalation: Get plenty of fresh air; in case of complications, seek medical attention. Skin contact: Wash skin with soap and rinse with water. Eye contact: Flush with pure water for at least 15 minutes immediately; seek medical attention. Ingestion: Drink plenty of water and seek immediate medical attention. Others: Remove soaked clothing immediately.

4. Fire fighting procedures:
Suitable extinguishing media: Water-spray, CO2, dry chemicals, foam. Unsuitable extinguishing media: High-pressure water jet. Exposure hazards: Thermal decomposition can lead to the generation of irritant vapor and gasses and/or fire. Special equipment: Pressure demand self-contained breathing apparatus should be provided to fire fighters in buildings.

5. Accidental release procedures:
Precautions - individuals: Wear protective equipment; use in a well-ventilated area and remove all sources of ignition.
Precautions - environment: Stop leaks as soon as possible and avoid discharge into environment.
Cleaning up spillage: Absorb with mineral filler (such as sand, diatomaceous earth, …) and store in a well sealed, suitable container.

6. Storage and handling:
Storage: Store in a well-sealed bottle in a well-ventilated room. Avoid temperatures exceeding 50º C; store away from food and from sources of ignition. Handling: Always use in a well-ventilated area. After use, close bottle immediately

7. Exposure control/individual protection
Constituents with limits relevant to the work are:
CAS No.: Description Type Value Unit
67-63-0 Isopropanol MAK 400 ppm
Individual:
Protection-hands: Protective gloves..
Protection-eyes: Protective glasses.
Protection-skin: Working coat (cotton).
General procedures with respect to individual hygiene: Avoid inhalation, do not eat eat, drink or smoke while working. After working,
wash your hands with soap and rinse with water thoroughly.

8. Physical and chemical properties:
Appearance:Liquid.
Color: Black.
Odor: Typical.
Data relevant to safety:
Melting point/interval: Approx. -88º C.
Boiling point/interval: Approx. 82 C.
Flash point: 12º C.
Ignition point: 425º C.
Self-inflammation: None.
Lower explosion limit: 2.0% by vol. Upper explosion limit: 12.0% by vol.
Vapor pressure (20º C): 42 mbar.

9. Stability and reactivity:
Conditions to avoid: Avoid temperatures exceeding 50 C.
Materials to avoid: Avoid strong oxidants.
Hazardous decomposition products: None on proper application.

10. Toxicological information:
Toxicological evaluation: The toxicological properties of this product have not been fully determined.
LD50/LC50: Substance Species Kind of exposure
5045 mg/hg Isopropanol Rat Oral
Sensitization: None have been reported yet.
Carcinogenic, teratogenic, or mutagenic effects: None have been reported yet.

11. Ecological information:
Avoid discharge into the environment.

12. Disposal consideration:
Product: This product has to be classified as chemical waste material and disposed in agreement with your local and national legislation.
Soiled container: Empty the bottle entirely and allow residues to evaporate in a well-ventilated place. Then dispose of container in agreement with your local and national regulations.

13. Export regulation
Transport:
By land:
ADR/RID/GGVS/GGVE class: 3 No./Letter: 3 b
Warning symbol: -- Hazard No.: -- Material No.: 1219
By air:
ICAO/IATA class: 3 UN/ID No.: 1219
Correct technical name: 2-propanol.

14. Regulatory information:
Hazard symbol and identification: F = Highly Flammable.
Hazardous substances: Isopropanol.
Hazard codes: R 11 Highly flammable.
Safety codes: S 7 Keep container tightly closed.
S 16 Keep away from sources of ignition.

Diephos Dentine Tooth Colored UV Die Spacer

Diephos Dentine is a light curing, tooth colored die spacer to be used when fabricating all ceramic restorations such as veneers or inlays. An excellent alternative to blue, green and red die spacers; it prevents the color of the die stone to shine through. This enhances the visual perception of the dental technician allowing them to create highly aesthetic restorations.

Benefits

Allows accurate shade matching to the patients dentition
Cures in 90 seconds (under 400nm or greater wavelength of UV light)
Applies quickly and evenly
Integrated brush in bottle cap
Makes die surfaces abrasion resistant

Exakto-Form Resin

INSTRUCTIONS FOR USE EXAKTO-FORM MODEL RESIN

Dual component model material, based on polyurethane, for fabricating extremely precise dental models. Thanks to its very low viscosity, it is easily poured into impressions without entrapping air voids. This cost-effective model resin features absolutely precise reproduction of surfaces, dimensional stability and unequaled precision of fit with no expansion whatsoever.

- Exakto-form model resin is supplied in cans containing 50 g. each of components A and B.
- 1 assortment includes 6 x 50 g. cans components A and 6 x 50 g. cans of component B.
- Both components are also available separately.

Directions - Application I

Always follow safety precautions!
Shake the tubs well before opening. Rip the lids off both tubs. To ensure that components A and B are mixed homogeneously, they must be stirred thoroughly before using, to mix the material which has settled.
Pour the contents of the component B tub into the tub containing component A (mixing ratio 1:1). Mix the two components thoroughly within 30 seconds. Working time is 2 to 3 minutes. Separate from impression after 30 minutes; maximum final hardness is achieved after 1.5 hours.

Application I

As this is a polyurethane based, dual-component material, it is inevitable that component B will react prematurely with the mixture in the atmosphere when the can is opened. Therefore, to prevent the moisture in the atmosphere from contacting the material for too long, and consequent premature setting, component B should be used immediately!

Directions - Application II

Should you require a small amount of Exakto-Form model resin (less than 100 g), you can fill the entire contents of tubs A & B into separate syringes and extrude the desired amount into a mixing vessel in a ratio of 1:1. Mix the two components thoroughly within 30 seconds. Working time 2-3 minutes. Separate from impression after 30 minutes. Maximum final hardness attained after 1.5 hours. Please make absolutely certain that you use the remaining material in the syringes within 2 days! Shake the tubs well before opening. Rip the lids off both cans. To ensure that components A & B are mixed homogeneously, they must be stirred thoroughly before each use to mix material which may have settled.

Application II

" Wear protective clothing, gloves, and glasses/face mask.
" In case of contact with the skin, wash immediately with plenty of soap and water.
" In case of contact with the eyes, rinse immediately with plenty of soap and water and seek medical attention immediately.
" Do not inhale vapors - use in well ventilated areas.
" In case of an accident or sudden indisposition, seek medical attention immediately (if possible, show package label).
" Keep out of reach of children.
" Keep out of sewage system, inshore waters, and earth.
" Keep away from open fire.
" GGVE/S 6 1 code 19 c.

The general industrial hygiene precautions applying to reactive resins and their hardeners should be followed.

MATERIAL SAFETY DATA SHEET
Product Name: EXAKTO FORM MODEL RESIN COMPONENT A - RESIN
Product Code: 520 001 74, 520 002 80

Before using this product, please read and follow these instructions carefully.

1. Composition/Information on ingredients
Product Description/use: Pigments in a mixture of solvents and polyols.
Hazardous Substances:
Name: CAS-No. Content Hazard symbols Hazard codes
White Spirit --- --- --- R 10

2. Hazard Identification
Hazard codes R 10 flammable.

3. First aid procedures:
Inhalation: Plenty of fresh air and in case of complications seek medical assistance. Skin contact: Wash skin with soap and rinse with plenty of water; in case of irritation seek medical attention. Eye contact: Flush immediately with pure water for at least 15 minutes; seek medical attention. Ingestion: Do not induce vomiting, and seek immediate medical attention. Others: Remove soaked clothing immediately.

4. Fire fighting procedures:
Suitable extinguishing media: Water-spray, CO2, dry chemicals, foam. Unsuitable extinguishing media: High-pressure water jet. Exposure hazards: Thermal decomposition can lead to the generation of irritant vapor and/or fire. Special equipment: Pressure demand self-contained breathing apparatus should be provided to fire fighters in buildings.

5. Accidental release procedures:
Precautions - individuals: Wear protective equipment; avoid contact with eyes and skin. Do not breathe vapor; always use in a well-ventilated area.
Precautions - environment: Stop leaks as soon as possible and avoid discharge into environment.
Cleaning up spillage: Absorb with mineral fillers (such as sand, diatomaceous earth,) and store in a well-sealed, suitable container.

6. Storage and handling:
Storage: Store in a well-sealed container in a well-ventilated room. Do not expose to temperatures exceeding 30º C; store away from food.
Handling: Avoid contact with eyes or skin; always use in a well-ventilated area; do not breathe vapor. Do not smoke. Keep away from sources of ignition.

7. Exposure control/individual protection
Individual:
Protection-hands: Protective gloves..
Protection-eyes: Protective glasses.
Protection-skin: Working coat (cotton).
General procedures with respect to individual hygiene: Avoid inhalation; avoid eye and skin contact. Do not eat, drink or smoke while.
working. After working, wash your hands with soap and water.

8. Physical and chemical properties:
Appearance:Liquid.
Color: Opaque, greenish.
Odor: Typical.
Data relevant to safety:
Acidity (pH): 10
Flash point: 42º C.
Ignition point: 420º C.
Self-inflammation: None.
Vapor pressure (20º C): 7-8 mbar.

9. Stability and reactivity:
Conditions to avoid: Do not expose to temperatures exceeding 50 C or below 5º C.
Materials to avoid: Avoid direct contact to strong oxidants or isocyanates.
Hazardous decomposition products: Thermal decomposition leads to the generation of irritant vapors.

10. Toxicological information:
Toxicological evaluation: The toxicological properties have not been fully determined.
Irritating properties: Direct contact with skin or eyes may cause irritation or reddening.
Sensitization: None have been reported yet.
Carcinogenic, teratogenic, or mutagenic effects: None have been reported yet.

11. Ecological information:
Avoid discharge into the environment.

12. Disposal consideration:
Product/Soiled container: Both need to be classified as chemical waste material and disposed of in agreement with your local and national legislation.

13. Export regulation
By land:
ADR/RID/GGVS/GGVE class: 3 No./Letter: 31.c)
Warning symbol: F Hazard No.: 30 Material No.: 1993
By air:
ICAO/IATA class: 3 UN/ID No.: 1993 Verp. Grp.: III/309
Correct technical name: White spirit.

14. Regulatory information:
Hazard symbol and identification: Flammable.
Hazard codes: R 10 Flammable.
Safety codes: S 16 Keep away from sources of ignition.
S 24/25 Avoid contact with eyes or skin.

MATERIAL SAFETY DATA SHEET
Product Name: EXAKTO FORM MODEL RESIN COMPONENT B - HARDENER
Product Code: 520 001 73, 520 002 80

Before using this product, please read and follow these instructions carefully.

1. Composition/Information on ingredients
Product Description/use: Hardener of a two compound model resin.
Name: CAS-No. Content Hazard symbols Hazard codes.
Dyphenylmethane-4,4' 101-68-8 Xn R 20; 36/37/38; 42
Diisocyanate.

2. Hazard Identification
Hazard codes: R 20 Harmful by inhalation.
R 36/37/38 Irritating to eyes, respiratory system & skin.
R 42 Sensitization may be caused by inhalation.

4. Fire fighting procedures:
Suitable extinguishing media: Water spray, CO2, dry chemicals, foam.
Unsuitable extinguishing media: High-pressure water jet.
Exposure hazards: High temperatures lead to the generation of irritant vapor and/or fire.

6. Storage and handling:
Storage: Store in a well-sealed glass container in a dry, well-ventilated room. Store at temperatures between 18 and 22º C; store away from food.
Handling: Avoid contact with eyes or skin; always use in a well-ventilated area; do not breathe vapor. Do not smoke.

7. Exposure control/individual protection
Constituents with limits relevant to the work area:
CAS-No.: Description: Type Value Unit
101-68-8 Diphenylmethane-4,4'-diisocyanate MAK 0.05 ppm
Individual:
Protection-hands: Protective gloves.
Protection-eyes: Protective glasses are recommended.
Protection-skin: Working coat (cotton).
General procedures with respect to individual hygiene: Avoid inhalation; avoid eye and skin contact. Do not eat, drink or smoke while working. After working, wash your hands with soap and rinse with water thoroughly.

8. Physical and chemical properties:
8. Physical and chemical properties
Appearance: Opaque liquid.
Color: Yellowish.
Odor: Typical.
Data relevant to safety:
Flash point: > 100º C.
Ignition point: 240º C.
Self-inflammation: No.
Vapor pressures (20º C): 8 mbar.
Specific density (20 C): 1.76 g/ml.

9. Stability and reactivity:
Conditions to avoid: Avoid temperatures exceeding 30 C and below 18º C.
Materials to avoid: Avoid peroxides, amins, alcohols and water.
Hazardous decomposition products: Reaction with water in a sealed container may cause a rising pressure and leads to the explosive destruction of the container.

10. Toxicological information:
Toxicological evaluation:
Acute toxicity:
LD50/LC50: Substance Species Kind of exposure
15000 mg/kg Diphenylmethane- Rat Oral
4,4'-diisocyanate
Irritating properties: Irritates mucous membranes, eyes and skin.
Sensitization: May cause sensitization symptoms like asthma.
Carcinogenic, teratogenic, or mutagenic effects: None have been reported yet.

11. Ecological information:
Avoid discharge into the environment.

12. Disposal consideration:
Product: This product needs to be classified as chemical waste material and disposed of in agreement with your local and national legislation.
Soiled container: Empty the bottle entirely; then dispose of in agreement with your local and national legislation.

13. Export regulation
Transport: Non-regulated.

14. Regulatory information:
Hazard symbol & identification: Xi = Irritant; F = Highly Flammable.
Hazardous substances: Methyl methacrylate.
Hazard codes: R 11 Highly flammable.
R 36/37/38 Irritates eyes, respiratory organs, and skin.
R 43 Direct skin contact may cause sensitization.
Safety codes: S 9 Store in well ventilated rooms only.
S 16 Avoid direct contact with sources of ignition-do not smoke.

1.Prior to mixing, each component must be stirred so that a homogeneous mixture is obtained. Mix the sediment completely.

2.Add component A to component B; empty tin completely.

3.Mix Exakto-Form approximately 30 seconds until a uniform color is obtained.

4.Two tins of Exakto-Form are sufficient to produce 2-3 complete dental arches.

5.The material can be removed after 30 minutes. Final hardness is achieved after 90 minutes. Then the model can be trimmed.

6.If a base for the model is to be produced with Exakto-Form, the model must first be insulated with Exakto-Form Insulating Liquid.

7.Due to its high edge stability, Exakto-form is perfectly suitable for precision-fit bridge and crown work.

8.Any technique can be used for sawing Exakto-Form models. Adopting a new technique is not required.

9.If smaller quantities are used, fill component A and B into separate syringes.

10.Pour equal quantities of Exakto-Form into a silicone beaker (approximately 2 ml for one die) and mix to obtain a homogeneous material. Please note, material in syringes must be used within 5 days.

11.Pour Exakto-Form into the impression. The excellent flow properties prevent the formation of bubbles even in impressions with thin edges.

12.The hardened resin can be drilled and trimmed. The stability avoids dimensional changes and guarantees precise models.

Gloss & Hardening Agent for Plasters

MATERIAL SAFETY DATA SHEET
Product Name: PLASTER SEALANT AND HARDENER
Product Code: 550 000 01, 550 000 02

Before using this product, please read and follow these instructions carefully.

1. Composition/Information on ingredients
Product Description/use: Solution of binders in various solvents.
Hazardous Substances:
Name:CAS-No.: Content Hazard symbols Hazard codes.
Acetone 67-64-1 70 - 90% by w. F R 11
Ethanol 67-17-5 0 - 30% by w. F R 11

2. Hazard Identification
Hazard codes: R 11 Highly flammable.

3. First aid procedures:
Inhalation: Get plenty of fresh air; in case of complications, seek medical attention.
Skin contact: Wash with soap and water; in case of irritation, seek medical attention.
Eye contact: Rinse eyes immediately for 10 to 15 minutes in running water, then seek medical attention.
Ingestion: Rinse mouth with pure water, do not induce vomiting, seek medical attention.
Others: Remove soaked clothing immediately.

4. Fire fighting procedures:
Suitable extinguishing media: CO2, dry chemicals or water-spray.
Unsuitable extinguishing media: High-pressure water jet.
Exposure hazards: Thermal decomposition can lead to the generation of toxic gases (NO2) and/or fire.
Special equipment: Pressure demand self-contained breathing apparatus should be provided to fire fighters in buildings.

5. Accidental release procedures:
Precautions - individuals: Wear suitable protective equipment; use adequate respiratory equipment, do not allow unprotected persons to enter the room.
Precautions - environment: Stop leaks as soon as possible and avoid discharge onto the environment.
Cleaning up spillage: Absorb with mineral fillers (such as sand, diatomaceous earth, …) and store in a well-sealed, suitable container. After vaporization of the remaining liquid, clean thoroughly with plenty of water.

6. Storage and handling:
Storage: Store in a well-sealed amber glass container. Do not expose to temperatures over 30º C.
Handling: Provide for good ventilation by local or general exhaust, clean the container after each use immediately.

7. Exposure control/individual protection
Constituents with limits relevant to the work are:
CAS-No.: Description: Type Value Unit
67-64-1 Acetone MAK 500 ppm
67-17-5 Ethanol MAK 1000 ppm
Individual:
Protection - hands: Protective gloves.
Protection - eyes: Protective glasses are recommended.
Protection - skin: Laboratory coat (cotton).
Protective and hygienic measures: Avoid inhalation as well as eye and skin contact, do not eat, drink or smoke while working. After working, wash your hands with soap and water; observe standard hygiene procedures.

8. Physical and chemical properties:
Appearance: Clear liquid.
Color: Colorless.
Odor: Typical.
Data relevant to safety:
Boiling point/interval: About 56 C.
Flash point: -18º C.
Ignition point: 465º C.
Self-inflammation: No.
Lower explosion limit: 2.6% by vol. Upper explosion limit: 13 % by vol.
Vapor pressure (20º C): 160 mbar.

9. Stability and reactivity:
Conditions to avoid: Avoid temperatures exceeding 40º C; avoid contact with heat sources or sources of ignition.
Materials to avoid: Avoid direct contact with strong oxidants.
Hazardous decomposition products: None on proper application, thermal decomposition leads to the generation of toxic gases (NO2, CO2, CO).

10. Toxicological information:
Toxicological evaluation: The toxicological properties have not been fully determined.
Acute toxicity:
LD50/LC50 : Substance Special Kind of exposure
5800 mg/kg Acetone Rat Oral
Irritating properties: Exposure to vapor for a long period of time may cause headaches, dizziness and nausea.

11. Ecological information:
Avoid discharge into the environment.

12. Disposal consideration:
Product: This product has to be classified as chemical waste material and disposed of in agreement with local and national regulations.
Soiled container: Empty the bottle completely and allow residues to evaporate in a well-ventilated area. Then dispose of container in agreement with local and national regulations.

13. Export regulation
Transport:
By land:
ADR/RID/GGVS/GGVE class: 3 No./Letter: 5 b
Warning symbol: F Hazard No.: Material No.: 1263.
By sea:
IMDG/GGVSea class: 3.2 No./Letter: 1263 Page: 3268.
EMS-No.: 3-05 MFAG: 310, 313
Correct technical name: Paint related material.
By air:
ICAO/IATA class: 3 UN/ID No. 1263.
Correct technical name: Paint related material.

14. Regulatory information:
Hazard symbol & identification: F Highly flammable.
Hazardous substances: Acetone, ethanol.
Hazard codes: R 11 Highly flammable.
Safety codes: S 9 Store in well-ventilated rooms only.
S 16 Avoid direct contact with sources of ignition - do not smoke.
S 23 Do not breathe vapor.

Without the hardening agent, models can be damaged when the restoration is placed on the model.

The special consistency leads to the diffusion into the plaster surface. The high edge stability and scratch resistance prevents most surface damage.

The gloss and hardening agent for plaster hardens after only 2 minutes.

Gloss and hardening agent for plaster diffuses into the plaster so that it can also be used on margins.

Isoplast Liquid

The brush pen allows application of the material in an economic and precise way.

Isoplast seals the surface and the plaster exhibits fine luster. This way the quality of the insulating layer can be checked.

Isoplast allows removal of the tray without damaging the model.

Light-curing Die Spacers

INSTRUCTIONS FOR USE DIE SPACER UV

Before using this product, please read and follow these instructions carefully.

1. Indication Range:
The die spacer light curing is a one-component liquid. This die spacer features a high abrasion resistance and therefore withstands high mechanical stress. This way the model die is protected against damage when fitting crowns and bridges.

2. Processing

2.1 Note
To create a cement gap, the die spacer must be polymerized immediately after the application. To harden preparation margins, apply a thin layer of die spacer; remove the excess die spacer with a paper towel before polymerization is started. The application of a thin layer will be sufficient to harden the surface of the die.
The light-curing die spacer allows the individual application of layers and - even on rough undersurfaces - forms a glass-like surface which is resistant to steam-jet blasting and can not be removed from the plaster die.

2.2 Preparation of the object
After the fabrication of the saw-cut model and the plaster dies, clean them with compressed air to obtain a dust-free surface. Then apply the desired layer thickness of die spacer light-curing. Please note: Plaster dies do not require pretreatment with die hardening and insulating agent.

2.3 Processing
Please note: Bottle must be sealed immediately after use.
Drip die spacer light-curing directly from the bottle onto a mixing block and then apply an evenly thin (approx. 10 ) layer of die spacer onto the model die (see item 2.5 Polymerization) using a disposable brush. If die spacer is applied too richly, it may run off and result in insufficient hardening

2.4 Layer thickness
The layer thickness can be adjusted by the repeated application of the spacer and by an intermediate polymerization process of the individual layers. Do not touch the spacer surface between the individual layers. Uneven application of layers must be corrected by applying a further layer so that the color becomes more intense and the layer thickness can be checked. After polymerizing, work can be immediately continued on the spacered die.

2.5 Polymerization
Please note: During light curing (polymerization) it must be ensured that the spacered surface is as close to the light outlet of the polymerization unit as possible. Dark spots must be avoided. Depending on the respective polymerization unit, the wetted surface must be cured as follows:
Polymerization times:
DentaColor Approx. 90 - 180 sec.
Bredent Polylux Approx. 180 - 240 sec.
Schütz PLC 5000 Approx. 180 - 240 sec.

3. Safety Recommendations and Hazard Warnings

3.1 Safety clothing
Die spacer light curing must be processed at a working place that is well ventilated. Open fire and smoking must be avoided. Do not inhale the vapors.

3.3 For safe handling of the die spacer light curing, please refer to the material safety data sheet.

3.4 In case of contact with the skin, mucous membrane or the eyes, rinse off the material with lots of water and seek medical attention.
If - after inhaling - complaints such as dizziness and nausea occur, seek medical attention immediately. In any case, please take the bottle and the material safety data sheet with you. While processing this die spacer, please keep food away from the working place.

4. Storage and Durability

4.1 Die spacer light curing must be stored at room temperature under dry conditions and protected against light.

4.2 If the bottle is sealed well and stored properly, the product has a shelf life of three years.

4.3 Proper disposal: please adhere to the information provided in the material safety data sheet.

5. Other Information
This information contained in these instructions for use is always updated according to the latest knowledge and experience.
Therefore, we recommend that you read these instructions again before using a new package.

INFORMATION REGARDING THE LIGHT STRENGTH OF THE DENTAL LIGHT CURING MACHINES

The wattage of the light bulb has no influence on the light curing process.
What is important is the wave-length of the radiation. In the dental market there are two different light types in use:
1) UV-A waves
2) UV-B waves
Some manufacturers of light curing tray materials use light bulbs which only send out UV-B waves. The reason is simple: the UV-B bulbs are cheaper than UV-A bulbs (you can buy them in an ordinary shop). These machines are very cheap but at the same time the customer is limited in its use. They also use photo-sensitive parts in their materials, which only react on UV-B light. The material, which is hardened with UV-B light, is very often not very stable, weak or a little bit soft. All dentists light curing machines send out only UV-B light because it is not permitted to use the stronger UV-A light inside the mouth (the soft tissue can be harmed).

Bredent uses photo-sensitive parts which only react on UV-A light (300-400 Nanometer) in order to provide the customer with high quality, hard and firm light curing materials. The bredent light curing machine "Polylux" is provided with a high quality UV-A bulb which can harden nearly all light curing materials in the dental market, also materials which contain UV-B sensitive parts.

Machines with insufficient results in combination with bredent light curing materials are:
ESPE Beta light curing machine
Triad, Dentsply
Voco, (the blue "tunnel")
Heräus-Kulzer (only the little one for tray material)
RSB

Machines with sufficient results are:
Bredent "Polylux" - light curing machine
ESPE Alpha - light curing machine (very small)
Heräus-Kulzer XS - light curing machine
Schütz - light curing machine
Ivoclar - light curing machine

MATERIAL SAFETY DATA SHEET
DIE SPACER BLUE PHOTO CURING
Product Code: 540 010 00

1. Composition/Information on ingredients
Product Description/use: Photo curing lacquer.
Hazardous Substances:
Name:CAS-No. Content Hazard symbols Hazard codes.
Methyl-methacrylate 80-62-6 40-60% by w. Xi; F R11; 36/37/38
Dipentaerythritol-pentaacrylate 60506-81-2 40-60% by w. Xi R36

2. Hazard Identification F Highly flammable.
Xi Irritant
Hazard codes R 11 Highly flammable.
R 36/37/38 Irritating to eyes, respiratory system & skin.
R 43 May cause sensitization with skin contact.

3. First aid procedures:
Inhalation: Plenty of fresh air and in case of complications seek medical assistance.
Skin contact: Wash skin with soap and rinse with water; in case of irritation, seek medical assistance.
Eye contact: Flush immediately with pure water for at least 15 minutes; seek medical attention.
Ingestion: Rinse mouth with purified water, do not induce vomiting, and seek immediate medical attention.
Others: Remove soaked clothing immediately.

4. Fire fighting procedures:
Suitable extinguishing media: Water-spray, CO2, dry chemicals, foam. Unsuitable extinguishing media: High-pressure water-jet. Exposure hazards: Thermal decomposition can lead to the generation of irritant vapor and gasses and/or fire. Special equipment: Pressure demand self-contained breathing apparatus be provided to fire fighters.

5. Accidental release procedures:
Precautions - individuals: Wear protective glasses, suitable gloves and protective clothing; use in a well-ventilated area and adequate respiratory equipment.
Precautions - environment: Stop leaks as soon as possible and avoid discharge into environment.
Cleaning up spillage: Absorb with mineral fillers (such as sand, diatomaceous earth,) and store in a well-sealed suitable container.

6. Storage and handling:
Storage: Store in a well-sealed black glass bottle in well-ventilated rooms only.
Conditions to be avoided: Do not expose to temperatures exceeding 30º C; do not expose to direct sunlight; store away from food.
Handling: Provide for good ventilation by local or general exhaust. Keep the container well sealed when stored and seal bottle immediately after each use.

7. Exposure control/individual protection
Constituents with limits relevant to the work area:
CAS-No. Description Type Value Unit
80-62-6 Methyl-methacrylate MAK 50 ppm
FURTHER DETAILS: BECAUSE THIS PRODUCT MAY BE HARMFUL TO UNBORN LIFE, DO NOT USE IT DURING PREGNANCY.
Individual:
Protection-hands: Protective gloves.
Protection-eyes: Protective glasses.
Protection-skin: Working coat (cotton).
General procedures with respect to individual hygiene: Avoid inhalation of the vapor, avoid eye and skin contact. Store working clothes separately, observe standard hygiene procedures.

8. Physical and chemical properties:
Appearance: Transparent liquid.
Color: Blue.
Odor: Typical.
Data relevant to safety:
Boiling point/interval: About 100 C.
Flash point: 10º C.
Ignition point: 430º C.
Self inflammation: No.
Lower explosion limit: 2.1% by vol. Upper explosion limit: 12.5% by vol.
Vapor pressure (20º C): 40 mbar.
Specific density: Approx. 1.0 g/ml.
Solubility in water (20 C; % by weight): Approx. 16,000 mg/l.

9. Stability and reactivity:
Conditions to avoid: Avoid temperatures exceeding 30 C; avoid direct sunlight or other UV-sources.
Materials to avoid: Peroxides, any source of free radicals and heavy metal ions.
Hazardous decomposition products: None when properly used; thermal decomposition can lead to the generation of irritant vapor and/or fire.

10. Toxicological information:
Toxicological evaluation: The toxicological properties of this product have not been fully determined.
Acute toxicity:
LD50/LC50: Substance Species Kind of exposure
8000 mg/kg Methyl-methacrylate Rat Oral
Irritating properties: Irritating to mucous membranes, eyes and skin.
Sensitization: Some cases of allergic reactions (headaches, irritation of eyes and skin) have been reported.
Carcinogenic, teratogenic, or mutagenic effects: None have been reported yet.

11. Ecological information:
Avoid discharge into the environment.

12. Disposal consideration:
Product/Soiled Container: Both need to be classified as chemical waste material and disposed in agreement with your local and national legislation.

13. Export regulation
Transport:
By land:
ADR/RID/GGVS/GGVE class: 3 No./Letter: 3 b
Warning symbol: Hazard No.: 339 Material No.: 1247
By ocean:
IMDG/GGV Sea class: 3.2 No./Letter: 1247 Ems: 3-07
Correct technical name: Methyl methacrylate monomer, inhibited.
By air:
ICAO/IATA class: 3 UN/ID No. 1247
Correct technical name: Methyl methacrylate monomer, inhibited.

14. Regulatory information:
Hazard symbol and identification: Xi = Irritant; F = Highly Flammable.
Hazardous substances: Methyl-Metacrylate.
Hazard codes: R 11 Highly Flammable.
R 36/37/38 Irritating to eyes, respiratory system and skin.
R 43 May cause sensitization with skin contact.
Safety codes: S 9 Store in well-ventilated rooms only.
S 16 Avoid direct contact with sources of ignition - no smoking.
S 26 In case of eye contact, flush eyes thoroughly with purified water and seek medical attention.
S 28 In case of skin contact, wash immediately with soap and water.
S 29 Avoid discharge into the environment and sewers.

DIE SPACER GREEN PHOTO CURING OPAQUE
Product Code: 540 001 03

1. Composition/Information on ingredients
Product Description/use: Photo curing paint.
Hazardous Substances:
Name: CAS-No. Content Hazard symbols Hazard codes
Methyl-methacrylate 80-62-6 40-60% by w. Xi; F R11; 36/37/38, 43
Dipentaerythritol-pentaacrylate 60506-81-2 40-60% by w. Xi R36

2. Hazard Identification
Hazard codes R 11 Highly flammable.
R 36/37/38 Irritating to eyes, respiratory system & skin.
R 43 May cause sensitization with skin contact.

3. First aid procedures
Inhalation: Plenty of fresh air and in case of complications seek medical assistance.
Skin contact: Wash skin with soap and rinse with water; in case of irritation, seek medical assistance.
Eye contact: Flush immediately with pure water for at least 15 minutes; seek medical attention.
Ingestion: Rinse mouth with purified water, do not induce vomiting, and seek immediate medical attention.
Others: Remove soaked clothing immediately.

4. Fire fighting procedures
Suitable extinguishing media: Water-spray, CO2, dry chemicals, foam.
Unsuitable extinguishing media: High-pressure water-jet.
Exposure hazards: Thermal decomposition can lead to the generation of irritant vapor and gasses and/or fire.
Special equipment: Pressure demand self-contained breathing apparatus be provided to fire fighters.

5. Accidental release procedures
Precautions - individuals: Wear protective equipment; use in a well-ventilated area, remove sources of ignition - no smoking.
Precautions - environment: Stop leaks as soon as possible and avoid discharge into environment.
Cleaning up spillage: Absorb with mineral fillers (such as sand, diatomaceous earth,) and store in a well-sealed suitable container.

6. Storage and handling
Storage: Store in a well-sealed black glass bottle in well-ventilated rooms only.
Conditions to be avoided: Do not expose to temperatures exceeding 30º C; do not expose to direct sunlight; store away from food.
Handling: Avoid contact with eyes or skin; always use in a well-ventilated area; do not breathe vapor. After use, close bottle immediately. Keep away from sources of ignition - no smoking.

7. Exposure control/individual protection
Constituents with limits relevant to the work area:
CAS-No. Description Type Value Unit
80-62-6 Methyl-methacrylate MAK 50 ppm
Individual:
Protection-hands: Protective gloves.
Protection-eyes: Protective glasses.
Protection-skin: Working coat (cotton).
General procedures with respect to individual hygiene: Store working clothes separately, do not eat eat, drink or smoke while working. After working, wash your hands with soap and rinse with water thoroughly.

8. Physical and chemical properties
Appearance: Opaque Liquid.
Color: Green.
Odor: Typical.
Data relevant to safety:
Boiling point/interval: 100 C.
Flash point: 10º C.
Ignition point: 430º C.
Self inflammation: No.
Lower explosion limit: 2.1% by vol. Upper explosion limit: 12.5 % by vol.
Vapor pressure (20º C): 40 mbar.
Specific density: Approx. 1.0 g/ml.
Solubility in water (20 C; % by weight): Approx. 16,000 mg/l.

9. Stability and reactivity
Conditions to avoid: Avoid exposing this product to temperatures exceeding 30 C; avoid direct sunlight or other UV-sources.
Materials to avoid: Strong oxidants.
Hazardous decomposition products: Thermal decomposition can lead to the generation of irritant vapor and/or fire.

10. Toxicological information
Toxicological evaluation: The toxicological properties of this product have not been fully determined.
Acute toxicity:
LD50/LC50: Substance Species Kind of exposure
8000 mg/kg Methyl-methacrylate Rat Oral
Irritating properties: Irritating to mucous membranes, eyes and skin.
Sensitization: Some cases of allergic reactions (headaches, irritation of eyes and skin) have been reported.
Carcinogenic, teratogenic, or mutagenic effects: None have been reported yet.

11. Ecological information
Avoid discharge into the environment.

12. Disposal consideration
Product/Soiled Container: Both need to be classified as chemical waste material and disposed in agreement with your local and national legislation.

13. Export regulation
Transport:
By land:
ADR/RID/GGVS/GGVE class: 3 No./Letter: 5 b Material No.: 1263
By air:
ICAO/IATA class: 3 UN/ID No. 1263
Correct technical name: Paint.

14. Regulatory information
Hazard symbol and identification: Xi = Irritant; F = Highly Flammable.
Hazardous substances: Methyl-Metacrylate.
Hazard codes: R 11 Highly Flammable.
R 36/37/38 Irritating to eyes, respiratory system and skin.
R 43 May cause sensitization with skin contact.
Safety codes: S 9 Store in well-ventilated rooms only.
S 16 Avoid direct contact with sources of ignition - no smoking.
S 26 In case of eye contact, flush eyes thoroughly with purified water and seek medical attention.
S 28 In case of skin contact, wash immediately with soap and water.

DIE SPACER YELLOW PHOTO CURING
Product Code: 540 010 04

1. Composition/Information on ingredients
Product Description/use: Photo curing lacquer.
Hazardous Substances:
Name: CAS-No. Content Hazard symbols Hazard codes
Methyl-methacrylate 80-62-6 40-60% by w. Xi; F R11; 36/37/38
Dipentaerythritol-pentaacrylate 60506-81-2 40-60% by w. Xi R36

2. Hazard Identification Xi = Irritant F = Highly flammable.
Hazard codes R 11 Highly flammable.
R 36/37/38 Irritating to eyes, respiratory system & skin.
R 43 May cause sensitization with skin contact.

5. Accidental release procedures
Precautions - individuals: Wear protective glasses, suitable gloves and protective clothing. Use in a well-ventilated area and adequate respiratory equipment.
Precautions - environment: Stop leaks as soon as possible and avoid discharge into environment.
Cleaning up spillage: Absorb with mineral fillers (such as sand, diatomaceous earth,) and store in a well-sealed suitable container.

6. Storage and handling
Storage: Store in a well-sealed black or amber glass bottle in well-ventilated rooms only. Do not expose to temperatures exceeding 30º C; do not expose to direct sunlight; store away from food.
Handling: Provide for good ventilation by local or general exhaust. Keep the bottle well sealed when stored and seal immediately after each use.

7. Exposure control/individual protection
Constituents with limits relevant to the work area:
CAS-No. Description Type Value Unit
80-62-6 Methyl-methacrylate MAK 50 ppm
Further details: This product may be harmful to unborn life, therefore, do not use during pregnancy.
Individual:
Protection-hands: Protective gloves.
Protection-eyes: Protective glasses are recommended.
Protection-skin: Working coat (cotton).
General procedures with respect to individual hygiene: Store working clothes separately, do not eat eat, drink or smoke while working. After working, wash your hands with soap and rinse with water thoroughly.

8. Physical and chemical properties
Appearance: Transparent liquid.
Color: Yellow.
Odor: Typical.
Data relevant to safety:
Boiling point/interval: About 100 C.
Flash point: 10º C.
Ignition point: 430º C.
Self inflammation: No.
Lower explosion limit: 2.1% by vol. Upper explosion limit: 12.5 % by vol.
Vapor pressure (20º C): 40 mbar.
Specific density: Approx. 1.0 g/ml.
Solubility in water (20 C; % by weight): Approx. 16,000 mg/l.

9. Stability and reactivity
Conditions to avoid: Avoid exposing this product to temperatures exceeding 30 C; avoid direct sunlight or other UV-sources.
Materials to avoid: Avoid peroxides, all sources of free radicals and heavy metal ions.
Hazardous decomposition products: None when properly used; thermal decomposition can lead to the generation of irritant vapor and/or fire.

11. Ecological information
Avoid discharge into the environment.

12. Disposal consideration
Product/Soiled Container: Both need to be classified as chemical waste material and disposed in agreement with your local and national legislation.

13. Export regulation
Transport:
By land:
ADR/RID/GGVS/GGVE class: 3 No./Letter: 3.6
Warning symbol: F Hazard No.: 339 Material No.: 1247
By sea:
IMDG/GGVSea class: 3.2 UN No.: 1247 EMS: 3-07
Correct technical name: Methyl methacrylate, monomer, inhibited.
By air:
ICAO/IATA class: 3 UN/ID No. 1247
Correct technical name: Methyl methacrylate, monomer, inhibited.

DIE SPACER GREEN PHOTO CURING
Product Code: 540 010 05

8. Physical and chemical properties
Appearance: Transparent liquid.
Color: Green.
Odor: Typical.
Data relevant to safety:
Boiling point/interval: About 100 C.
Flash point: 10º C.
Ignition point: 430º C.
Self inflammation: No.
Lower explosion limit: 2.1% by vol. Upper explosion limit: 12.5 % by vol.
Vapor pressure (20º C): 40 mbar.
Specific density: Approx. 1.0 g/ml.
Solubility in water (20 C; % by weight): Approx. 16,000 mg/l.

11. Ecological information
Avoid discharge into the environment.

12. Disposal consideration
Product/Soiled Container: Both need to be classified as chemical waste material and disposed in agreement with your local and national legislation.

DIE SPACER TRANSPARENT PHOTO CURING
Product Code: 540 010 06

7. Exposure control/individual protection
Constituents with limits relevant to the work area:
CAS-No. Description Type Value Unit
80-62-6 Methyl-methacrylate MAK 210 mg/cm3
80-62-6 Methyl-methacrylate MAK 50 ppm
FURTHER DETAILS: THIS PRODUCT MAY BE HARMFUL TO UNBORN LIFE, THEREFORE, DO NOT USE DURING PREGNANCY.
Individual:
Protection-hands: Protective gloves.
Protection-eyes: Protective glasses are recommended.
Protection-skin: Working coat (cotton).
General procedures with respect to individual hygiene: Store working clothes separately, do not eat eat, drink or smoke while working. After working, wash your hands with soap and rinse with water thoroughly.

8. Physical and chemical properties
Appearance: Clear liquid.
Color: Yellowish.
Odor: Typical.
Data relevant to safety:
Boiling point/interval: About 100 C.
Flash point: 10º C.
Ignition point: 430º C.
Self inflammation: No.
Lower explosion limit: 2.1% by vol. Upper explosion limit: 12.5 % by vol.
Vapor pressure (20º C): 40 mbar.
Specific density: Approx. 1.0 g/ml.
Solubility in water (20 C; % by weight): Approx. 16,000 mg/l.

9. Stability and reactivity
Conditions to avoid: Avoid exposing this product to temperatures exceeding 30 C; avoid direct sunlight or other UV-sources; avoid direct contact with heat sources.
Materials to avoid: Avoid peroxides, all sources of free radicals and heavy metal ions.
Hazardous decomposition products: None when properly used.

11. Ecological information
Avoid discharge into the environment.

12. Disposal consideration
Product/Soiled Container: Both need to be classified as chemical waste material and disposed in agreement with your local and national legislation.

13. Export regulation
Transport:
By land:
ADR/RID/GGVS/GGVE class: 3 No./Letter: 56 Material No.: 1263
By air:
ICAO/IATA class: 3 UN/ID No. 1263
Correct technical name: Lacquer.

MATERIAL SAFETY DATA SHEET
DIE SPACER BLUE PHOTO CURING OPAQUE
Product Code: 540 001 01

2. Hazard Identification
Hazard codes R 11 Highly flammable.
R 36/37/38 Irritating to eyes, respiratory system & skin.
R 43 May cause sensitization with skin contact.

7. Exposure control/individual protection
Constituents with limits relevant to the work area:
CAS-No. Description Type Value Unit
80-62-6 Methyl-methacrylate MAK 50 ppm
Individual:
Protection-hands: Protective gloves.
Protection-eyes: Protective glasses.
Protection-skin: Working coat (cotton).
General procedures with respect to individual hygiene: Avoid inhalation of the vapor, avoid eye and skin contact. Store working clothes separately, do not eat eat, drink or smoke while working. After working, wash your hands with soap and rinse with water thoroughly; observe standard hygiene procedures.

8. Physical and chemical properties
Appearance: Opaque Liquid.
Color: Blue.
Odor: Typical.
Data relevant to safety:
Boiling point/interval: 100 C.
Flash point: 10º C.
Ignition point: 430º C.
Self inflammation: No.
Lower explosion limit: 2.1% by volume Upper explosion limit: 12.5 % by volume
Vapor pressure (20º C): 40 mbar.
Specific density: Approx. 1.0 g/ml.
Solubility in water (20 C; % by weight): Approx. 16,000 mg/l.

11. Ecological information
Avoid discharge into the environment.

12. Disposal consideration
Product/Soiled Container: Both need to be classified as chemical waste material and disposed in agreement with your local and national legislation.

13. Export regulation
Transport:
By land:
ADR/RID/GGVS/GGVE class: 3 No./Letter: 5 b Material No.: 1263
By ocean:
IMDG/GGV Sea class: 3.2 No./Letter: 1247 Page: 3259
EMS-No.: 3-07 MFAG: 330
Correct technical name: Methyl methacrylate monomer, inhibited.
By air:
ICAO/IATA class: 3 UN/ID No. 1247
Correct technical name: Methyl methacrylate monomer, inhibited.

DIE SPACER GREEN PHOTO CURING OPAQUE
Product Code: 540 001 03

2. Hazard Identification
Hazard codes R 11 Highly flammable.
R 36/37/38 Irritating to eyes, respiratory system & skin.
R 43 May cause sensitization with skin contact.

11. Ecological information
Avoid discharge into the environment.

12. Disposal consideration
Product/Soiled Container: Both need to be classified as chemical waste material and disposed in agreement with your local and national legislation.

13. Export regulation
Transport:
By land:
ADR/RID/GGVS/GGVE class: 3 No./Letter: 5 b Material No.: 1263
By air:
ICAO/IATA class: 3 UN/ID No. 1263
Correct technical name: Paint.

DIE SPACER RED PHOTO CURING OPAQUE
Product Code: 540 001 04

2. Hazard Identification F = Highly flammable Xi = Irritant
Hazard codes R 11 Highly flammable.
R 36/37/38 Irritating to eyes, respiratory system and skin.
R 43 May cause sensitization with skin contact.

3. First aid procedures
Inhalation: Plenty of fresh air and in case of complications seek medical assistance.
Skin contact: Wash skin with soap and rinse with water; in case of irritation, seek medical assistance.v
Eye contact: Flush immediately with pure water for at least 15 minutes; seek medical attention.
Ingestion: Rinse mouth with purified water, do not induce vomiting, and seek immediate medical attention.
Others: Remove soaked clothing immediately.

5. Accidental release procedures
Precautions - individuals: Wear protective equipment. Use in a well-ventilated area, remove sources of ignition - do not smoke.
Precautions - environment: Stop leaks as soon as possible and avoid discharge into environment.
Cleaning up spillage: Absorb with mineral fillers (such as sand, diatomaceous earth,) and store in a well-sealed suitable container.

6. Storage and handling
Storage: Store in a well-sealed amber or black glass container in well-ventilated room.
Conditions to be avoided: Do not expose to temperatures exceeding 30º C; do not expose to direct sunlight; store away from food.
Handling: Provide for good ventilation by local or general exhaust, keep the bottle well-sealed when store, and seal immediately after each use.

7. Exposure control/individual protection
Constituents with limits relevant to the work area:
CAS-No. Description Type Value Unit
80-62-6 Methyl-methacrylate MAK 50 ppm
Individual:
Protection-hands: Protective gloves.
Protection-eyes: Protective glasses are recommended.
Protection-skin: Working coat (cotton).
General procedures with respect to individual hygiene: Store working clothes separately, do not eat eat, drink or smoke while working. After working, wash your hands with soap and rinse with water thoroughly.

8. Physical and chemical properties
Appearance: Opaque liquid.
Color: Red.
Odor: Typical.
Data relevant to safety:
Boiling point/interval: About 100 C.
Flash point: 10º C.
Ignition point: 430º C.
Self inflammation: No.
Lower explosion limit: 2.1% by vol. Upper explosion limit: 12.5 % by vol.
Vapor pressure (20º C): 40 mbar.
Specific density: Approx. 1.0 g/ml.
Solubility in water (20 C; % by weight): Approx. 16,000 mg/l.

9. Stability and reactivity
Conditions to avoid: Avoid exposing this product to temperatures exceeding 30 C; avoid direct sunlight or other UV-sources.
Materials to avoid: Avoid peroxides, all sources of free radicals and heavy metal ions.
Hazardous decomposition products: Thermal decomposition can lead to the generation of irritant vapor and/or fire.

11. Ecological information
Avoid discharge into the environment.

12. Disposal consideration
Product/Soiled Container: Both need to be classified as chemical waste material and disposed in agreement with your local and national legislation.

13. Export regulation
Transport:
By land:
ADR/RID/GGVS/GGVE class: 3 No./Letter: 5 b Material No.: 1263
By air:
ICAO/IATA class: 3 UN/ID No. 1263
Correct technical name: Paint.

14. Regulatory information
Hazard symbol and identification: Xi = Irritant; F = Highly flammable.
Hazardous substances: Methyl-Metacrylate.
Hazard codes: R 11 Highly Flammable.
R 36/37/38 Irritating to eyes, respiratory system and skin.
R 43 May cause sensitization with skin contact.
Safety codes: S 9 Store in well-ventilated rooms only.
S 16 Avoid direct contact with sources of ignition - no smoking.
S 26 In case of eye contact, flush eyes thoroughly with purified water and seek medical attention.
S 28 In case of skin contact, wash immediately with soap and water.

Light-curing Die Spacer (Transparent)

The disposable brush allows precise application. The layer thickness can be varied by applying the material several times.

The varnishes are translucent. If they are applied several times, the color becomes more intense so that the layer thickness can be gauged.

The light curing die varnishes produce a particularly hard surface which protects the die against damage when fitting onto the crowns.

To produce a cement gap the varnish must be cured immediately after applying. For hardening of preparation margins: allow die to soak into the plaster, then polymerize. The varnish hardens the surface without layering.

Light-curing Die Spacer (Opaque)

Light-curing die varnish is available in three different opaque colors. The fine masking capacity allows to obtain a uniform color of the varnish layer.

During the application the die varnish diffuses into the plaster surface. Depth polymerization leads to abrasion resistant bonding to the die. Light curing die varnish resists high mechanical stress. Even steam blasting the units does not affect the strong bonding.

Microceramic

In the field of crowns and bridges, Microceramic is especially suitable for non-precious alloys since very cast surfaces are obtained. The Microceramic is adapted to the expansion of the investment material.

The difference after sandblasting with glass beads can be clearly recognized: The entire oxide layer can be easily removed so that less working time is required.

An extended processing time span allows precise application of the Microceramic. Microscopically fine ceramic particles ensure perfect reproduction of very fine details of wax models.

Devesting is simplified since there is no bonding between the investment material and Microceramic.

Microceramic avoids extreme formation of oxide on non-precious metal alloys. Cast objects are only sandblasted with 50 micron glass beads to obtain almost perfect high luster. Consequently, time for further processing is saved.

INSTRUCTIONS FOR USE MICROCERAMIC

Before using this product, please read and follow these instructions carefully.

1. Indication Range:
Microceramic is used for non-precious metal alloys in the field of crowns and bridges as well as for CoCr denturework to reduce the oxide layer and to obtain a fine metal surface.

2. Processing
Loosen the Microceramic by slightly pressing the bottle and then shaking it vigorously until a uniform consistency is obtained and the ball moves in the bottle. If required, dilute with distilled water to obtain a creamy consistency.
Use a brush to apply a thin layer of Microceramic onto the wax pattern; ensure that the pattern is completely covered with Microceramic. It is important to avoid the formation of puddles on occlusal surfaces and in the area of the palate. Invest immediately after the Microceramic material has been applied.
After casting, devest the object as usual. Sandblast the Microceramic and adhering oxides using fine or medium coarse abrasive material (110 mµ). Any material for polish blasting can be used for crowns and bridges.

3. Safety Recommendations and Hazard Warnings
" Do not inhale Microceramic dust. The dust contains quartz. In case of repeated exposure, the risk of silicosis exists.
" Microceramic dust should only be removed from the working place with a moist cloth.
" To avoid the formation of dust when deflasking, place the flask into water for a short time after it has cooled down.
" When sandblasting the casting, always use a fine dust filter extraction system.

4. Other Information
The information contained in these instructions is always updated according to the latest knowledge and experience. Therefore, we recommend that you read these instructions again before using a new package. These instructions refer to Microceramic, Item #550 000 12.

MATERIAL SAFETY DATA SHEET
Product Name: MICROCERAMIC
Product Code: 550 000 12

Before using this product, please read and follow these instructions carefully.

1. Composition/Information on ingredients
Product Description/use: Mixture of silicone dioxide with inorganic metal oxide pigments. Contains soda water glass CAS 1344-09-08.

2. Possible hazards:None

3. First aid procedures:
Exposure: Not applicable.
Skin contact: Rinse with plenty of water.
Eye contact: Rinse with plenty of water.
Recommended emergency equipment: Not applicable.

4. Fire fighting procedures:
Suitable extinguishing media: All.
Special hazards caused by the product of its product of combustion: None, this product is not flammable.

5. Accidental release procedures:
After spillage, do not absorb dried material.

6. Storage and handling:
Storage: This product must be stored in dry rooms and in the sealed original container.
Handling: The container must always be closed. General measures of hygiene must be adhered to. Adequate protection measures must be followed.

7. Exposure control/individual protection:
Technical measures: None.
Personal protective equipment: Not applicable.

8. Physical and chemical properties:
Appearance: Paste.
Color: Green.
Odor: None.
Melting point: Not applicable.
Thermal decomposition: Not applicable.
Density: Approx. 1500 kg/m3
Vapor pressure: Not applicable.
pH-Value: Neutral.
Solubility in water: Partly soluble.
Additional information: None.

9. Stability and reactivity:
Conditions to avoid: Not applicable.
Materials to avoid: Not applicable.
Hazardous decomposition products/protection measures: None.

10. Toxicological information:
This product is toxic. If adequate handling is followed, observation of dust protection measures and proper use are ensured, this product will not have any effects that are harmful to health.

11. Ecological information:
This product consists mainly of mineral substances occurring in nature.
Water hazard class: 0 (self-classification).

12. Disposal consideration:
This product can be disposed of together with household waste if the regulations of the local authorities are adhered to.
Disposal method for packaging material: Not applicable.
We would like to point out that national or regional regulations might be applicable.

13. Transport information:
This product is not subject to the regulations on the transport of hazardous products.

14. Regulatory information:
Labeling: Fine investment material is not a hazardous substance according to the definition - Ordinance on Hazardous Materials.
Information on the label: None.

15. Other information
Training information/instructions: Not applicable.
Recommended use/restrictions: Not applicable.
Data sheet completed by: Research & Development Dept. - Bredent (Germany).
This Material Safety Data Sheet is provided by way of guide for the use of our product and is correct to the best of our knowledge. However, we can't offer any guarantee as to its accuracy or exhaustiveness. All chemicals may present unforeseen risks and should be used with caution. We cannot guarantee that the risks referred above are the only risks present. The final choice of the application of a product is thus the sole responsibility of the user.

Oxide-Stop Precious

Prevents polished, precious and semi precious alloy surfaces from oxidizing while being soldered with a flame or in a furnace and while firing porcelain.

Oxide Stop MSDS

Oxide-Stop Precious forms a protective layer during firing which prevents the metal surface from oxidizing.

Oxide-Stop Precious maintains the high luster. No refinishing is required.

Refinishing oxidized surfaces reduces the material and may adversely affect the precision of fit.

MATERIAL SAFETY DATA SHEET
Product Name: THINNER FOR OXIDE STOP PM
Product Code: 520 006 70

Before using this product, please read and follow these instructions carefully.

1. Composition/Information on ingredients
Product Description/use: Thinner.
Hazardous substances:
Name: CAS-No.: Content Hazard symbol Hazard codes
Xylenes 1330-20-7 15-25% by w. Xn R 10, R 20/21, R 38

2. Hazard Identification Xn Harmful
Hazard codes: R 10 Flammable.
R 20/21 Harmful by inhalation and in contact with skin.
R38 Irritant to skin.

3. First aid procedures:
Inhalation: Plenty of fresh air, rest the injured person softly, seek medical assistance.
Skin contact: Wash skin with soap and rinse with water. In case of irritation, seek medical attention.
Eye contact: Flush immediately with pure water for at least 15 minutes; seek medical attention.
Ingestion: Seek medical attention immediately. Others: Remove soaked clothing immediately.

4. Fire fighting procedures:
Suitable extinguishing media: Water-spray, CO2, dry chemicals, foam.
Unsuitable extinguishing media: High-pressure water-jet.
Exposure hazards: Thermal decomposition can lead to the generation of irritant vapor and/or fire.
Special equipment: Pressure demand self-contained breathing apparatus should be provided to fire fighters in buildings.

5. Accidental release procedures:
Precautions - individuals: Wear protective equipment, use in well-ventilated area - do not inhale vapor, remove all sources of ignition immediately.
Precautions - environment: Stop leaks as soon as possible and avoid discharge into environment.
Cleaning up spillage: Absorb with mineral fillers (such as sand, diatomaceous earth, …) and store in a well sealed, suitable container.

6. Storage and handling:
Storage: Store in a well-sealed container in well ventilated rooms only.
Conditions to be avoided: Do not expose to temperatures exceeding 30º C; store away from food.
Handling: Do not breathe vapor; keep away from sources of ignition - no smoking. After using, close the bottle immediately.

7. Exposure control/individual protection:
Constituents with limits relevant to work area:
CAS No. Description Type Value Unit
1330-20-7 Xylenes MAK 100 ppm
Individual:
Protection-hands: Protective gloves.
Protection-eyes: Protective glasses.
Protection-skin: Working coat (cotton).
General procedures with respect to individual hygiene: Do not eat, drink or smoke while working. After working, wash your hands with soap and rinse with water thoroughly.

8. Physical and chemical properties:
Appearance: Clear liquid.
Color: Red.
Odor: Typical.
Data relevant to safety:
Boiling point/interval: 140 C.
Flash point: 23-27º C.
Ignition point: > 460º C.
Self-Inflammation: None.
Lower explosion limit: 1% by vol. Upper explosion limit: 8% by vol.
Vapor pressure (20º C): 7-8 mbar.

9. Stability and reactivity:
Conditions to avoid: Do not expose to temperatures exceeding 30º C. Keep away from sources of ignition - do not smoke.
Materials to avoid: Avoid direct contact to strong oxidants or alkali.
Hazardous decomposition products: Thermal decomposition leads to the generation of irritant vapor.

10. Toxicological information:
Toxicological evaluation: The toxicological properties have not been fully determined.
Acute toxicity:
LD50/LC50: Substance Species Kind of exposure
4300 mg/kg Xylene Rat Oral
Irritating properties: Irritating to skin.
Sensitization: None have been reported yet.
Carcinogenic, teratogenic or mutagenic effects: None have been reported yet.

11. Ecological information:
Avoid discharge into the environment.

12. Disposal consideration:
Product: This product has to be classified as chemical waste material and disposed in agreement with your local and national regulations.
Soiled container: Empty the bottle entirely and allow residues to evaporate in a well-ventilated area. Then dispose of the container in agreement with your local and national regulations.

13. Export regulation
By land:
ADR/RID/GGVS/GGVE class: 3 No./Letter: 31.c)
Warning symbol: 3 Material No.: 1307
By air:
ICAO/IATA class: 3 UN/ID No.: 1307 Verp. Grp.: III/309
Correct technical name: Xylenes

14. Regulatory information:
Hazard symbol & identification: Xn = Harmful.
Hazardous substances: Xylenes.
Hazard codes: R 10 Flammable.
R 20/21 Harmful by inhalation and in contact with skin.
R 38 Irritant to skin.
Safety codes: S 23 Do not breathe vapor.
S 24/25 Avoid contact with eyes or skin.

Plaster Separating Liquid

The plaster separating liquid soaks into the plaster and seals the surface without layering. The pen brush allows quick application.

The spray bottle insulates large areas within a short time. The fine spray mist ensures uniform.

The gap-free fit ensures maximum precision.

The plaster separating liquid allows separating of the base and the arch without any damage.

MATERIAL SAFETY DATA SHEET
Product Name: PLASTER COATING SOLUTION
Product Code: 540 001 35

Before using this product, please read and follow these instructions carefully.

1. Composition/Information on ingredients
Product Description/Use: Mixture of salts and natural binders in aqueous solution.

2. Hazard Identification
Hazard codes: According to "GefStoffV", this product is not classified as a hazardous substance. Nevertheless, direct contact may cause irritation of the eyes in some cases.

3. First aid procedures:
Inhalation: Get plenty of fresh air; in case of complications, seek medical attention.
Skin contact: Wash skin with soap and plenty of water; in case of irritation, seek medical attention.
Eye contact: Flush with pure water for at least 15 minutes immediately; then seek medical attention.
Ingestion: Drink plenty of water; seek medical attention immediately.
Others: Remove soaked clothing immediately.

4. Fire fighting procedures:
Suitable extinguishing media: This product is not flammable.
Exposure hazards: High temperatures lead to the generation of irritant vapor.
Special equipment: Pressure demand self-contained breathing apparatus be provided to fire fighters.

5. Accidental release procedures:
Precautions - individuals: Wear protective equipment.
Precautions - environment: Stop leaks as soon as possible and avoid discharge into environment.
Cleaning up spillage: Absorb with mineral filler (such as sand, diatomaceous earth … ), collect and store in a suitable container.

6. Storage and handling:
Storage: Store in a well-sealed container. Do not expose to temperatures below 5º C or exceeding 30º C, store away from food.
Handling: Avoid direct contact with eyes, close bottle after use.

7. Exposure control/individual protection:
Individual:
Protection - hands: None.
Protection - eyes: Protective glasses are recommended.
Protection - body: Working coat (cotton).
General procedures with respect to individual hygiene: Do not eat, drink or smoke when working. After working, wash your hands with soap and rise with water.

8. Physical and chemical properties:
Appearance: Clear liquid.
Color: Reddish.
Odor: Typical.
Acidity (pH, % by weight in water): 6.5 - 7.5.
Data relevant to safety:
Boiling point/interval: About 100º C.
Vapor pressure (20º C): 23 hPa.
Specific density (20º C): 1.0 g/ml.
Solubility in water (20º C; % by weight): Soluble mg/l.

9. Stability and reactivity:
Conditions to avoid: Avoid temperatures below 5º C.

10. Toxicological information:
Toxicological evaluation: The toxicological properties of this product have not been determined.
Irritating properties: Irritation of the eyes may occur in rare cases after direct contact.
Sensitization: None have been reported yet.
Carcinogenic teratogenic or mutagenic effects: None have been reported yet.

11. Ecological information:
Avoid discharge into the environment.

12. Disposal consideration:
Product: This product has to be classified as chemical waste material and disposed of in agreement with local and national regulations.
Soiled Container: Empty the bottle entirely, rinse with plenty of water and dispose of in agreement with local and national regulations.

13. Export regulation
Transport: Non-regulated.

14. Regulatory information:
Hazard symbol and identification: According to "GefStoffV", this product is not classified as a hazardous substance.
Safety Codes: S 2 Keep out of reach of children.

15. Other information
Data sheet completed by: Research & Development Department - Bredent (Germany).
This Material Safety Data Sheet is provided by way of guide to the use of our product and is correct to the best of our knowledge.
However, we can't offer any guarantee as to its accuracy or exhaustiveness. All chemicals may present unforeseen risks and should be used with caution.
We cannot guarantee that the risks referred above are the only risks present. The final choice of the application of a product is thus the sole responsibility of the user.

Plaster Solvent

MATERIAL SAFETY DATA SHEET
Product Name: DENTACLEAN PLASTER SOLVENT
Product Code: 520 009 93

Before using this product, please read and follow these instructions carefully.

1. Composition/Information on ingredients
Preparation: Corrosive solid for removing oxides from precious metals.
Description: Gelatin agent in aqueous solution.
Hazardous constituents:
Name: CAS-No. Content Hazard Symbol Hazard Codes
Ethylene diamine tetra-acetic 2005739 20-30% by w. Xi R 36
Acid, tetrasodium salt

2. Hazard Identification F Flammable
Hazard codes: R 36 Irritates the eyes.

3. First aid procedures:
In general: Dispose of soiled clothing.
Inhalation: Get plenty of fresh air and keep calm. Seek medical attention.
Skin contact: Wash the affected area thoroughly with soap and water.
Eye contact: Rinse eyes for at least 15 minutes in running water. Seek medical attention.
Ingestion: Rise mouth immediately and drink copious amounts of water. Seek medical immediately.

4. Fire fighting procedures:
Suitable extinguishing media: Dry agent, water, CO2, foam.
Unsuitable extinguishing media: High-pressure water jet

5. Accidental release procedures:
Precautions - individuals: Wear a protective suit; avoid contact eyes and skin.
Precautions - environment: This product must not be introduced into inland waters without being treated in advance (biological sewerage works).
Cleaning up spillage: Absorb with general-purpose binder and dispose of.

6. Storage and handling:
Storage: Keep the container tightly closed, store in a cool, and dry place.
Handling: Ventilate the work area well.

7. Exposure control/individual protection
Individual:
Respiratory protection: Avoid inhaling the vapors.
Hand protection: Safety gloves.
Eye protection: Safety glasses.
Body protection: Laboratory coat.
Protective and hygienic measures: Do not eat, drink or smoke while working. Wash your hands after working.

8. Physical and chemical properties:
Appearance:
Form: Liquid.
Color: Yellowish.
Odor: Characteristic.
Data relevant to safety:
pH value at 10 g/l H2O and 23º C: Approx. 11
Change of state:
Boiling point/range: Approx. 100º C g/l
Flash point: > 100º C g/l
Ignition point: > 200º C g/l
Density (23º C): Approx. 1.3 g/lcm3 g/l
Solubility in water (20º C): Unlimited solubility g/l
Viscosity (at 23º C): Approx. 23 mPas g/l

9. Stability and reactivity:
Conditions to avoid: Corrodes aluminum.

10. Toxicological information:
Irritation/etching: Irritates the eyes.

11. Ecological information:
If low concentrations are introduced correctly into adapted biological sewerage works, decomposition in biological sludge ought not to be impeded.
Ecological-toxic effects:
Aquatic toxicity:
Organism Test duration Test method Result
Leucisions idus 96 hours EC/LC50 > 500 mg/l

12. Disposal consideration:
Product: This product has to be classified as chemical waste material and should be disposed of in agreement with local regulatory requirements.
Soiled container: Packaging which cannot be cleaned must be disposed of like the substance itself.

13. Export regulation
Transport by land:
ADR/RID/GGVS/GGVE class: 8 No./Letter: 56 c
Warning symbol: Hazard No.: 80 Material No.: 3267
Description of goods: Corrosive liquid, basic, organic n.a.g.
Transport by sea:
INDG/GGVSea class: 8 UN No.: 3267 PG: 8147-1
EMS: 8-15 MFAG: 760
Marine pollutant: Corrosive liquid, basic, organic, N.O.S.
Transport by air:
ICAO/IATA class: 8 UN No.: 3267 Packaging Group II
Correct technical name: Ethylene diamine tetra-acetic acid tetrasodium salt solution in water.

14. Regulatory information:
Hazard symbol & identification: Xi Irritant.
Hazardous substances: Ethylene diamine tetra-acetic acid tetrasodium salt.
Hazard codes: R 36 Irritating to eyes.
Safety codes: S 2 Keep out of reach of children.
S 26 In case of contact with eyes, rinse immediately with plenty of water and seek medical attention.
S 36 Wear suitable protective clothing.

Porcelain Mixing Liquid

MATERIAL SAFETY DATA SHEET
Product Name: PORCELAIN MIXING LIQUID
Product Code: 520 001 23, 520 008 60

Before using this product, please read and follow these instructions carefully.

1. Composition/Information on ingredients
Product Description/use: Aqueous solution of several alcohols.
Name: CAS-No. Content Hazard symbols Hazard codes
1.3 - Butanediol 107-88-0 Xi R 36/37/38

2. Hazard Identification F Flammable
Hazard codes R 36/37/38 Irritating to eyes, respiratory system & skin.

3. First aid procedures:
Inhalation: Plenty of fresh air and in case of complications seek medical assistance.
Skin contact: Wash skin with soap and rinse with plenty of water.
Eye contact: Flush immediately with pure water for at least 15 minutes; seek medical attention.
Ingestion: Drink plenty of water, do not induce vomiting, and seek immediate medical attention.
Others: Remove soaked clothing immediately.

4. Fire fighting procedures:
Suitable extinguishing media: Water, CO2, dry chemicals, foam.
Exposure hazards: Thermal decomposition can lead to the generation of irritant vapor.

6. Storage and handling:
Storage: Store in a well-sealed bottle. Avoid temperatures exceeding 50º C; store away from food.
Handling: Avoid contact with eyes or skin; always use in a well-ventilated area; do not breathe vapor. After use, close bottle as soon as possible.

7. Exposure control/individual protection
Individual:
Protection-hands: Protective gloves.
Protection-eyes: Protective glasses.
Protection-skin: Working coat (cotton).
General procedures with respect to individual hygiene: Do not eat, drink or smoke while working. After working, wash your hands with soap and rinse with water thoroughly.

8. Physical and chemical properties:
Appearance: Liquid.
Color: Blue.
Odor: Aromatic.
Acidity (pH, % by weight in water): 7 - 8
Data relevant to safety:
Boiling point/interval: 100 C.
Vapor pressure (20º C): About 24 mbar.
Solubility in water (20 C; % by weight): Soluble.

9. Stability and reactivity:
Conditions to avoid: Avoid exposing this product to temperatures exceeding 50 C.
Materials to avoid: Strong oxidants.
Hazardous decomposition products: Thermal decomposition can lead to the generation of irritant vapor and toxic gases such as CO and Co2.

10. Toxicological information:
Toxicological evaluation: The toxicological properties of this product have not been fully determined.
Irritating properties: Exposure to the vapor from this product may cause irritation of eyes and mucous membranes.
Sensitization: None have been reported yet.
Carcinogenic, teratogenic, or mutagenic effects: None have been reported yet.

11. Ecological information:
Avoid discharge into the environment.

12. Disposal consideration:
Product/Soiled Container: Both need to be classified as chemical waste material and disposed in agreement with your local and national legislation.

13. Regulatory information
Hazardous substances: 1.3 - Butanediol
Hazard codes: R 36/37/38 Irritating to eyes, respiratory system and skin.
Safety codes: S 24/25 Avoid contact with eyes and skin.
S 2 Keep out of the reach of children.

14. Other information
Data sheet completed by: Research & Development Dept. - Bredent (Germany).
This Material Safety Data Sheet is provided by way of guide for the use of our product and is correct to the best of our knowledge. However, we can't offer any guarantee as to its accuracy or exhaustiveness. All chemicals may present unforeseen risks and should be used with caution. We cannot guarantee that the risks referred above are the only risks present. The final choice of the application of a product is thus the sole responsibility of the user.

Ropak Light Curing Pink Opaquer

INSTRUCTIONS FOR USE ROPAK - UV

Before using this product, please read and follow these instructions carefully.

1. Indication Range:
Ropak UV is a light curing resin-colored opaque to cover CoCr objects that are to be veneered with cold-polymerizing, pink resin. Due to its special color, Ropak UV ensures perfect covering of all metal parts.

2. Processing
2.1 Preparation of the object
Blast the metal frame using aluminum oxide or corundum. After blasting, the metal surface must be dust- and fat-free.

2.2 Mixing
Mix Ropak UV powder and liquid to obtain a liquid consistency.
Please note: Do not mix Ropak UV so that the consistency is too thick since this will result in incomplete curing.

2.3 Applying
Apply Ropak UV in a very thin, covering layer using a disposable brush. Then polymerize in the light-curing unit as described under item 2.4.

2.4 Polymerization times in the light curing unit
Denta-Color XS 90 sec.
Schütz PLC 5000 5 min.
Bredent PolyLux 5 min.
Please note: The object should always be placed as close as possible to the light source. The luminous intensity, and thus the effect, decreases considerably if the distance to the light source increases, so that insufficient polymerization may result. Shade spots must be avoided.

3. Sources of Errors
3.1 Formation of "clouds" and discoloration in the resin.
Error: Ropak UV has not been cured long enough in the light curing unit.
The layer of Ropak UV that has been applied is too thick.
The material has been cured in an unsuitable light-curing unit.

3.2 Despite sufficiently long curing times, Ropak UV still exhibits greasiness on the surface
Error: The layer of Ropak UV is too thick.
Solution: Remove Ropak UV by sandblasting the frame (object), mix it to obtain a thinner consistency and apply anew.

4. Safety Recommendations and Hazard Warnings
4.1 Protective clothing: while working with Ropak UV, protective clothing must be worn.
4.2 For safe handling of Ropak UV, please refer to the material safety data sheet.
4.3 In case of contact with the skin, mucous membranes or eyes, rinse off with water immediately.

5. Storage and Durability
5.1 Ropak UV powder must be stored under dry conditions at room temperature. Ropak UV liquid must be sealed immediately after taking a certain quantity out of the container.
5.2 Proper disposal: Please adhere to the information on the product provided in the material safety data sheet.

6. Further Information
The information contained in this product information is always updated according to the latest knowledge and experience. Therefore, we recommend to read this product information again before using a new package.
This product information refers to:
Ropak UV Liquid Item # 520 001 64, and
Ropak UV Powder Item # 520 001 65.

INFORMATION REGARDING THE LIGHT STRENGTH OF THE DENTAL LIGHT CURING MACHINES

MATERIAL SAFETY DATA SHEET
Product Name: ROPAK UV LIQUID
Product Code: 520 001 64

Before using this product, please read and follow these instructions carefully.

1. Composition/Information on ingredients
Product Description/Use: Photo curing lacquer.
Hazardous Substances: CAS-No Content Hazard Symbols Hazard Codes
Methyl-methacrylate 80-62-6 40 - 60% Xi; F R 11, 36/37/38
Dipentaerythritol-pentaacrylate 60506-31-2 40 - 60% Xi R 36

2. Hazard Identification
Hazard Codes: F = Highly Flammable Xi = Irritant
R11 Highly Flammable
R 36/37/38 Irritant to eyes, respiratory organs and skin
R 43 May cause sensitization through skin contact

3. First aid procedures:
Inhalation: Get plenty of fresh air; in case of complications seek medical assistance.
Skin contact: Wash with soap, rinse with water. In case of irritation, seek medical attention.
Eye contact: Rinse eyes under pure water for at least 15 minutes immediately; seek medical attention.
Ingestion: Rinse mouth with pure water, do not induce vomiting, seek medical attention immediately.
Others: Remove soaked clothing immediately.

4. Fire fighting procedures:
Suitable extinguishing media: Water spray, foam, dry chemicals, CO2.
Unsuitable extinguishing media: High-pressure water jet.
Exposure hazards: Thermal decomposition can lead to the generation of irritant vapor (acrylic acid) and/or fire.
Special equipment: Pressure demand self-contained breathing apparatus should be provided to fire fighters in buildings.

5. Accidental release procedures:
Precautions - individuals: Ensure adequate ventilation, wear protective glasses, suitable gloves and protective clothing, use adequate respiratory equipment.
Precautions - environment: Stop leaks as soon as possible; avoid discharge into the environment.
Cleaning up spillage: Absorb with mineral filler (such as sand, diatomaceous earth, …), collect and store in a suitable, well-sealed container.

6. Storage and handling:
Storage: Store in a well-sealed amber or black glass container in a well-ventilated room. Do not expose to temperatures exceeding 30º C or to direct sunlight.
Handling: Ensure good ventilation by local or general exhaust, keep the container well sealed during storage; seal bottle tightly after each use.

7. Exposure control/individual protection
Constituents with limits relevant to the work area:
CAS-No. Description Type Value Unit
80-62-6 Methyl-methacrylate MAK 50 ppm
FURTHER DETAILS: AS THIS PRODUCT COULD BE HARMFUL TO UNBORN LIFE, DO NOT USE IT DURING PREGNANCY.
Individual:
Protection - hands: Protective gloves.
Protection - eyes: Protective glasses are recommended.
Protection - body: Working coat (cotton).
General procedures with respect to individual hygiene: Avoid breathing vapor, avoid eye and skin contact, store working clothes separately; do not eat, drink or smoke while working, after working wash your hands with soap and water; observe standard hygiene procedures.

8. Physical and chemical properties:
Appearance: Transparent liquid.
Color: Colorless.
Odor: Typical.
Data relevant to safety:
Acidity (acid value, mg KGH7g): No data available.
Acidity (pH, % by weight): No data available.
Melting point/interval: No data available.
Boiling point/interval: Approx. 100º C.
Flash point: 10º C.
Ignition point: 430º C.
Self-inflammation: No.
Lower explosion limit: 2.1 % by volume Upper explosion limit: 12.5 % by volume
Vapor pressure (20º C): 40 mbar.
Specific density: Approx. 1.0 g/ml.
Solubility in water (20º C; % by weight): Approx. 16000 mg/l.

9. Stability and reactivity:
Conditions to avoid: Temperatures exceeding 30º C.
Materials to avoid: Peroxides, any sources of free radicals and heavy metal ions.
Hazardous decomposition products: None on proper application; thermal decomposition leads to the generation of irritant vapor and/or fire.

10. Toxicological information:
Toxicological evaluation: The toxicological properties of this product have not been fully determined.
Acute toxicity:
LD50/LC50: Substance Species Kind of Exposure
8000 mg/kg Methyl-methacrylate Rat Oral
Irritating properties: Irritates mucous membranes, eyes and skin.
Sensitization: Allergic reactions (headaches, eye and skin irritation) have been noticed in some cases.
Carcinogenic, teratogenic or mutagenic effects: None have been reported yet.

11. Ecological information:
Avoid discharge into the environment.

12. Disposal consideration:
Product/Soiled container: This product has to be classified as chemical waste material and disposed of in agreement with local and national regulations.

13. Export regulation
Transport:
By Land:
ADR/RID/GGVS/GGVE class: 3 No./Letter: 3.b)
Warning Symbol: F Hazard No.: Material No.: 1247
By Water (Ships):
IMDG/GGVSea class: 3.2 UN No.: 1247 Ems: 3-07
MFAG: 330
Correct technical name: Methyl methacrylate, monomer, inhibited.
By Air:
ICAO/IATA class: 3 UN/ID No.: 1247
Correct technical name: Methyl methacrylate, monomer, inhibited.

14. Regulatory information:
Hazard symbol and identification: Xi = Irritant; F = Highly Flammable.
Hazardous substances: Methyl methacrylate.
Hazard Codes: R 11 Highly Flammable.
R 36/37/38 Irritates eyes, respiratory organs and skin.
R 43 May cause sensitization through skin contact.
Safety Codes: S 9 Store in well-ventilated rooms only.
S 16 Avoid direct contact with sources of ignition; do not smoke.
S 26 In case of eye contact, flush thoroughly with pure water and seek medical attention.
S 28 In case of skin contact, wash immediately with soap and water.

15. Other information
Data sheet completed by: Research & Development Department - Bredent (Germany).
This Material Safety Data Sheet is provided by way of guide for the use of our product and is correct to the best of our knowledge.
However, we can't offer any guarantee as to its accuracy or exhaustiveness. All chemicals may present unforeseen risks and should be used with caution.
We cannot guarantee that the risks referred above are the only risks present. The final choice of the application of a product is thus the sole responsibility of the user.

Seracoll UV Light-Curing Wax Adhesive

Seracoll UV is a new light curing wax adhesive liquid from Bredent that is designed for use in creating stress-free connections in C&B and implant bar wax-ups. It is also suitable for fabricating wax-ups for the copy milling technique. Seracoll UV is totally homogenous with waxes and cures in any light curing unit with a UV or LED wavelength range of 270 – 580 nanometers in approximately 10 seconds; and, it burns – out clean and residue-free. This light curing liquid adhesive for waxes is highly accurate and saves time compared to using pattern resins for similar applications.

Low viscosity
Versatile
Clean burning
Convenient packaging prevents spillage during use

Light curing, cures in all dental units
Highly accurate and stable
Saves time

CompoForm UV

CompoForm UV can be used in conjuction with modelling wax and is perfectly suitable for interlocking the model prior to investing. This way investing without any deformation is possible.

Modelling and further processing of telescopic and conical crowns can be perfectly controlled by means of a visual check of the layer. The high stability of the hardened composite allows reworking with a bur.

Thanks to low shrinkage and burning without any residue, the composite is ideal for fixation of bridges to be soldered.

Model cast extensions can be fabricated in a simple and time-saving manner. compoForm UV can be easily removed from the plaster.

Undercuts on dies can be quickly and completely blocked out.

Burning without any residue and reduced swelling behavior provide perfect preconditions for top-quality casting results.

Separating Agents

Separating Agent for Ceramic	MSDS Download
Thinner for Separating Agent for Ceramic	MSDS Download
FGP Insulating Agent	MSDS Download
Master-Sep Insulating Liquid	MSDS Download
Isoflex Ceramic Insulating Liquid	MSDS Download
Pi-Ku-Plast Separating Liquid	MSDS Download
KG Sorensen Brush Disposable Applicators	MSDS Download

Silicone & Wax Surface Tension Reducing Agent

The spraying head of the spray bottle simplifies uniform wetting surface with silicone and wax tension reducing agent.

After the application of the agent onto the surface (above), the flow characteristics of the plaster have been clearly improved.

Silicone and wax surface tension reducing agent produces a homogeneous plaster surface. This will ensure precise dental work.

MATERIAL SAFETY DATA SHEET
Product Name: SILICONE AND WAX SURFACE TENSION REDUCER
Product Code: 540 007 05

Before using this product, please read and follow these instructions carefully.

1. Composition/Information on ingredients
Product Description/use: Solution of special substances in 2-propanol.
Hazardous substances:
Name: CAS-No. Content Hazard symbol Hazard codes
2-propanol. 67-63-0 85% by weight F R11

2. Hazard Identification
Hazard codes: R 11 Highly flammable.

3. First aid procedures:
Inhalation: Plenty of fresh air and in case of complications seek medical assistance.
Skin contact: Wash skin with soap and rinse with water.
Eye contact: Flush eyes immediately with pure water for at least 15 minutes; seek medical attention.
Ingestion: Drink plenty of water, do not induce vomiting, seek medical attention immediately.
Others: Remove soaked clothing immediately.

4. Fire fighting procedures:
Suitable extinguishing media: Water-spray, CO2, dry chemicals, foam.
Unsuitable extinguishing media: High-pressure water jet.
Exposure hazards: Thermal decomposition can lead to the generation of irritant vapor and/or fire.
Special equipment: Pressure demand self-contained breathing apparatus should be provided to fire fighters in buildings.

5. Accidental release procedures:
Precautions - individuals: Do not inhale vapor; use in well-ventilated areas. Keep away from sources of ignition - do not smoke
Precautions - environment: Avoid discharge into the environment.
Cleaning up spillage: Absorb with mineral fillers (such as sand, diatomaceous earth,) and store in a well-sealed suitable container. Be careful, danger of skidding!

6. Storage and handling:
Storage: Store in a well-sealed container in well-ventilated rooms only. Avoid temperatures exceeding 35º C; keep away from food and from sources of ignition - do not smoke.
Handling: Do not breathe vapor. After use, close container immediately; use in well-ventilated areas only.

7. Exposure control/individual protection:
Constituents with limits relevant to the work area:
CAS-No.: Description: Type Value Unit
67-63-0 2-propanol MAK 400 ppm
Individual:
Protection-hands: Protective gloves.
Protection-eyes: Protective glasses.
Protection-skin: Working coat (cotton).
General procedures with respect to individual hygiene: Do not eat, drink or smoke while working. After working, wash your hands with soap and rinse with water thoroughly.

8. Physical and chemical properties:
Appearance: Liquid.
Color: Blue.
Odor: Typical
Acidity (pH, % b weight in water): 6.5
Data relevant to safety:
Boiling point/interval: 82 C.
Flash point: < 21º C.
Ignition point: 425º C.
Self-inflammation: None.
Lower explosion limit: 2.0% by vol. Upper explosion limit: 12% by vol.
Vapor pressure (20º C): 42 mbar.
Specific density: 0.84 g/ml.
Solubility in water (20 C; % by weight): Soluble.

9. Stability and reactivity:
Conditions to avoid: Avoid temperatures exceeding 35 C.
Materials to avoid: Avoid strong oxidants.
Hazardous decomposition products: None with proper use.

10. Toxicological information:
Toxicological evaluation: The toxicological properties have not been fully determined.
Acute toxicity:
LD50/LC50: Substance Species Kind of exposure
5045 mg/kg 2-propanol Rat Oral
Sensitization: None have been reported yet.
Carcinogenic, teratogenic, or mutagenic effects: None have been reported yet.

11. Ecological information:
Avoid discharge into the environment.

12. Disposal consideration:
Product: This product has to be classified as chemical waste material and disposed in agreement with your local and national legislation.
Soiled container: Empty the bottle entirely and allow residues to evaporate in a well-ventilated area; then dispose of container in agreement with your local and national regulations.

13. Export regulation
By land:
ADR/RID/GGVS/GGVE class: 3 No./Letter: 3 b
Warning symbol: F Material No: 1219
By air:
ICAO/IATA class: 3 UN/ID No. 1219.
Correct technical name: 2-propanol.

14. Regulatory information:
Hazard symbol and identification: F Highly flammable.
Hazardous substances: 2-propanol.
Hazard codes: R 11 Highly flammable.
Safety codes: S 7 Keep container tightly closed.
S 16 Keep away from sources of ignition - no smoking.

Stain Liquid

MATERIAL SAFETY DATA SHEET
Product Name: STAIN LIQUIDS
Product Code: 520 001 21, 520 008 40

Before using this product, please read and follow these instructions carefully.

1. Composition/Information on ingredients
Product Description/use: Aqueous solution of bi-functional alcohols.
Name: CAS-No. Content Hazard symbols Hazard codes
Menthol 15356-70-4 < 5% by w. Xi R 36/37/38

2. Hazard Identification Xi Irritant
Hazard codes R 36/37/38 Irritating to eyes, respiratory system & skin.

3. First aid procedures:
Inhalation: Get plenty of fresh air and in case of complications seek medical assistance.
Skin contact: Wash skin with soap and rinse with plenty of water.
Eye contact: Flush immediately with pure water for at least 15 minutes; seek medical attention.
Ingestion: Seek medical attention immediately.
Others: Remove soaked clothing immediately.

4. Fire fighting procedures:
Suitable extinguishing media: Water, CO2, dry chemicals, foam.
Exposure hazards: Thermal decomposition can lead to the generation of irritant vapor and gases and/or fire.
Special equipment: Pressure demand self-contained breathing apparatus should be provided to fire fighters in buildings.

5. Accidental release procedures:
Precautions - individuals: Avoid contact with eyes and skin. Do not breathe vapor; use in a well-ventilated area and do not allow unprotected persons to enter the room.
Precautions - environment: Stop leaks as soon as possible and avoid discharge into environment.
Cleaning up spillage: Absorb with mineral fillers (such as sand, diatomaceous earth,) and store in a well-sealed suitable container.

6. Storage and handling:
Storage: Store in a well-sealed bottle in well-ventilated rooms only. Avoid temperatures exceeding 40º C; store away from food.
Handling: Avoid contact with eyes or skin; always use in a well-ventilated area; do not breathe vapor. After use, close bottle as soon as possible.

8. Physical and chemical properties:
Appearance: Clear liquid.
Color: Colorless.
Odor: Like peppermint.
Acidity (pH, % by weight in water): 7.0 - 7.5
Data relevant to safety:
Boiling point/interval: >200 C.
Flash point: 108º C.
Ignition point: 375º C.
Vapor pressure (20º C): 2.4 mbar.
Specific density: 0.99 g/ml
Solubility in water (20 C; % by weight): Soluble.

9. Stability and reactivity:
Conditions to avoid: Thermal decomposition.
Materials to avoid: Strong oxidants.
Hazardous decomposition products: Thermal decomposition can lead to the generation of irritant vapor and toxic gases.

10. Toxicological information:
Toxicological evaluation: The toxicological properties of this product have not been fully determined.
Irritating properties: Irritant to eyes, respiratory organs and skin.
Sensitization: None have been reported yet.
Carcinogenic, teratogenic, or mutagenic effects: None have been reported yet.

11. Ecological information:
Avoid discharge into the environment.

12. Disposal consideration:
Product/Soiled Container: Both need to be classified as chemical waste material and disposed in agreement with your local and national legislation.

13. Regulatory information
Hazard symbol and identification: Xi = Irritant.
Hazardous substances: Menthol.
Hazard codes: R 36/37/38 Irritating to eyes, respiratory system and skin.
Safety codes: S 36/37/39 Wear suitable protective gloves and protective glasses.

14. Other information
Data sheet completed by: Research & Development Dept. - Bredent (Germany).
This Material Safety Data Sheet is provided by way of guide for the use of our product and is correct to the best of our knowledge.
However, we can't offer any guarantee as to its accuracy or exhaustiveness. All chemicals may present unforeseen risks and should be used with caution.
We cannot guarantee that the risks referred above are the only risks present. The final choice of the application of a product is thus the sole responsibility of the user.

BREDENT LIQUIDS SUPPORT

Ceram-Bond

1. Indication Range

2. Processing

2.1. Preparation of the object:

2.2. Applying Ceram Bond:

2.3. Predrying Ceram Bond in the ceramic furnace:

2.4. Firing Ceram Bond in the ceramic furnace:

2.5. Opaque firing and further processing:

3. Error sources and their elimination:

3.1. Cracks in Ceram Bond:

3.2. Bubbles in Ceram Bond:

3.3. Green and/or blacks spots in Ceram Bond:

3.4 Cracks in the ceramic:

4. Safety recommendations and hazard warnings

4.1. Personal protective equipment:

4.2. Skin contact:

4.3. Eye contact:

4.4. After swallowing:

5. Storage and durability:

5.1. The product must be stored in the sealed container under dry conditions. If proper storage is ensured, the product features unlimited durability.

5.2. Proper disposal: Ceram Bond can be disposed of together with the regular household garbage.

6. Additional information

Chrome Cobalt Bonding Agent

INSTRUCTIONS FOR USE CHROME COBALT BONDING AGENT

MATERIAL SAFETY DATA SHEETProduct Name: CHROME COBALT BONDING AGENTProduct Code: 520 003 20, 520 003 21

1. Pre-treating the metal coping

2. Applying the bonding agent

3. Firing the chrome cobalt bonding agent

Cracks in the chrome cobalt bonding agent:

Blisters in the chrome cobalt bonding agent:

Green/Black spots:

Cracks in the porcelain:

To date, only three alloys have been proven unsuitable :

Microanalysis of the porcelain content

Colloidal Graphite

MATERIAL SAFETY DATA SHEETProduct Name: COLLOIDAL GRAPHITEProduct Code: 540 007 06

Diephos Dentine Tooth Colored UV Die Spacer

Diephos Dentine Tooth Colored UV Die Spacer

Exakto-Form Resin

INSTRUCTIONS FOR USE EXAKTO-FORM MODEL RESIN

MATERIAL SAFETY DATA SHEETProduct Name: EXAKTO FORM MODEL RESIN COMPONENT A - RESINProduct Code: 520 001 74, 520 002 80

MATERIAL SAFETY DATA SHEETProduct Name: EXAKTO FORM MODEL RESIN COMPONENT B - HARDENERProduct Code: 520 001 73, 520 002 80

Gloss & Hardening Agent for Plasters

MATERIAL SAFETY DATA SHEETProduct Name: PLASTER SEALANT AND HARDENERProduct Code: 550 000 01, 550 000 02

Isoplast Liquid

Light-curing Die Spacers

INSTRUCTIONS FOR USE DIE SPACER UV

INFORMATION REGARDING THE LIGHT STRENGTH OF THE DENTAL LIGHT CURING MACHINES

MATERIAL SAFETY DATA SHEETDIE SPACER BLUE PHOTO CURINGProduct Code: 540 010 00

DIE SPACER GREEN PHOTO CURING OPAQUE Product Code: 540 001 03

DIE SPACER YELLOW PHOTO CURING Product Code: 540 010 04

DIE SPACER GREEN PHOTO CURING Product Code: 540 010 05

DIE SPACER TRANSPARENT PHOTO CURING Product Code: 540 010 06

MATERIAL SAFETY DATA SHEET DIE SPACER BLUE PHOTO CURING OPAQUE Product Code: 540 001 01

DIE SPACER GREEN PHOTO CURING OPAQUE Product Code: 540 001 03

DIE SPACER RED PHOTO CURING OPAQUE Product Code: 540 001 04

Light-curing Die Spacer (Transparent)

Light-curing Die Spacer (Opaque)

Microceramic

INSTRUCTIONS FOR USE MICROCERAMIC

MATERIAL SAFETY DATA SHEET Product Name: MICROCERAMIC Product Code: 550 000 12

Oxide-Stop Precious

Oxide-Stop Precious

MATERIAL SAFETY DATA SHEET Product Name: THINNER FOR OXIDE STOP PM Product Code: 520 006 70

Plaster Separating Liquid

MATERIAL SAFETY DATA SHEET Product Name: PLASTER COATING SOLUTION Product Code: 540 001 35

Plaster Solvent

MATERIAL SAFETY DATA SHEET Product Name: DENTACLEAN PLASTER SOLVENT Product Code: 520 009 93

Porcelain Mixing Liquid

MATERIAL SAFETY DATA SHEET Product Name: PORCELAIN MIXING LIQUID Product Code: 520 001 23, 520 008 60

Ropak Light Curing Pink Opaquer

INSTRUCTIONS FOR USE ROPAK - UV

INFORMATION REGARDING THE LIGHT STRENGTH OF THE DENTAL LIGHT CURING MACHINES

MATERIAL SAFETY DATA SHEET Product Name: ROPAK UV LIQUID Product Code: 520 001 64

Seracoll UV Light-Curing Wax Adhesive

Seracoll UV Light-Curing Wax Adhesive

CompoForm UV

Separating Agents

Silicone & Wax Surface Tension Reducing Agent

MATERIAL SAFETY DATA SHEET
Product Name: CHROME COBALT BONDING AGENT
Product Code: 520 003 20, 520 003 21

MATERIAL SAFETY DATA SHEET
Product Name: COLLOIDAL GRAPHITE
Product Code: 540 007 06

MATERIAL SAFETY DATA SHEET
Product Name: EXAKTO FORM MODEL RESIN COMPONENT A - RESIN
Product Code: 520 001 74, 520 002 80

MATERIAL SAFETY DATA SHEET
Product Name: EXAKTO FORM MODEL RESIN COMPONENT B - HARDENER
Product Code: 520 001 73, 520 002 80

MATERIAL SAFETY DATA SHEET
Product Name: PLASTER SEALANT AND HARDENER
Product Code: 550 000 01, 550 000 02

MATERIAL SAFETY DATA SHEET
DIE SPACER BLUE PHOTO CURING
Product Code: 540 010 00

DIE SPACER GREEN PHOTO CURING OPAQUE
Product Code: 540 001 03

DIE SPACER YELLOW PHOTO CURING
Product Code: 540 010 04

DIE SPACER GREEN PHOTO CURING
Product Code: 540 010 05

DIE SPACER TRANSPARENT PHOTO CURING
Product Code: 540 010 06

MATERIAL SAFETY DATA SHEET
DIE SPACER BLUE PHOTO CURING OPAQUE
Product Code: 540 001 01

DIE SPACER GREEN PHOTO CURING OPAQUE
Product Code: 540 001 03

DIE SPACER RED PHOTO CURING OPAQUE
Product Code: 540 001 04

MATERIAL SAFETY DATA SHEET
Product Name: MICROCERAMIC
Product Code: 550 000 12

MATERIAL SAFETY DATA SHEET
Product Name: THINNER FOR OXIDE STOP PM
Product Code: 520 006 70

MATERIAL SAFETY DATA SHEET
Product Name: PLASTER COATING SOLUTION
Product Code: 540 001 35

MATERIAL SAFETY DATA SHEET
Product Name: DENTACLEAN PLASTER SOLVENT
Product Code: 520 009 93

MATERIAL SAFETY DATA SHEET
Product Name: PORCELAIN MIXING LIQUID
Product Code: 520 001 23, 520 008 60

MATERIAL SAFETY DATA SHEET
Product Name: ROPAK UV LIQUID
Product Code: 520 001 64

MATERIAL SAFETY DATA SHEET
Product Name: SILICONE AND WAX SURFACE TENSION REDUCER
Product Code: 540 007 05

MATERIAL SAFETY DATA SHEET
Product Name: STAIN LIQUIDS
Product Code: 520 001 21, 520 008 40